Difference between revisions of "Aufgaben:Exercise 4.8: Near-end and Far-end Crosstalk Disorders"
Line 3: | Line 3: | ||
}} | }} | ||
− | [[File:EN_LZI_A_4_8.png|right|frame| | + | [[File:EN_LZI_A_4_8.png|right|frame|For local and long-distance crosstalk]] |
− | + | On the $S_0$ bus at [[Examples_of_Communication_Systems/Allgemeine_Beschreibung_von_ISDN|$\rm ISDN$]] (''Integrated Services Digital Networks''), data is transmitted separately according to transmission direction on a four-wire line. The received signal of an ISDN device is therefore disturbed not only by connections on other wires but also by crosstalk from its own transmitted signal. | |
− | In | + | In this exercise, two ISDN terminals with $\text{50 m}$ distance are considered, assuming: |
− | * | + | * For the power density spectrum (PDS) of the transmitter of each terminal, let ${\it\Phi}_{0} = 5 \cdot 10^{-9} \ \rm W/Hz$ be very simplified: |
:$${\it\Phi}_{s}(f)= \left\{ \begin{array}{c} {\it\Phi}_{0} \\ | :$${\it\Phi}_{s}(f)= \left\{ \begin{array}{c} {\it\Phi}_{0} \\ | ||
0 \end{array} \right. | 0 \end{array} \right. | ||
Line 15: | Line 15: | ||
{ |f| > f_0\hspace{0.05cm}.} | { |f| > f_0\hspace{0.05cm}.} | ||
\end{array}$$ | \end{array}$$ | ||
− | * | + | * The power transfer function on the $S_0$ bus $\text{(0.6 mm}$ copper two–wire line, $\text{50 m)}$ is to be approximated in the considered range $0 < |f| < 100 \ \rm kHz$ as follows (very simplified) angenähert werden: |
:$$|H_{\rm K}(f)|^2 = 0.9 - 0.04 \cdot \frac{|f|}{\rm 1 \ MHz}\hspace{0.05cm}.$$ | :$$|H_{\rm K}(f)|^2 = 0.9 - 0.04 \cdot \frac{|f|}{\rm 1 \ MHz}\hspace{0.05cm}.$$ | ||
− | * | + | * The near–end crosstalk power transfer function is given as follows $(\rm NEXT$ stands for ''near–end crosstalk''$)$: |
:$$|H_{\rm NEXT}(f)|^2 = \left ( K_{\rm NEXT} \cdot |f|\right )^{3/2}\hspace{0.05cm},\hspace{0.2cm}K_{\rm | :$$|H_{\rm NEXT}(f)|^2 = \left ( K_{\rm NEXT} \cdot |f|\right )^{3/2}\hspace{0.05cm},\hspace{0.2cm}K_{\rm | ||
NEXT} = 6 \cdot 10^{-10}\,{\rm s} | NEXT} = 6 \cdot 10^{-10}\,{\rm s} | ||
\hspace{0.05cm}.$$ | \hspace{0.05cm}.$$ | ||
− | + | The diagram shows the system configuration under consideration. Two twisted pairs connect subscribers $1$ and $2$ (one in each direction), while on two other twisted pairs (not in the same four-wire line) there is a connection between subscriber $3$ and subscriber $4$. | |
Line 31: | Line 31: | ||
− | '' | + | ''Notes:'' |
− | * | + | *The exercise belongs to the chapter [[Linear_and_Time_Invariant_Systems/Eigenschaften_von_Kupfer–Doppeladern|Properties of Balanced Copper Pairs]]. |
− | * | + | *It also refers to the chapter [[Examples_of_Communication_Systems/ISDN-Basisanschluss|ISDN Basic Access]] in the book "Examples of Communication Systems". |
Line 40: | Line 40: | ||
− | === | + | ===Questions=== |
<quiz display=simple> | <quiz display=simple> | ||
− | { | + | {Which of the following statements are true? |
|type="[]"} | |type="[]"} | ||
− | - | + | - Transmitter $S_1$ leads to near-end crosstalk at receiver $E_2$. |
− | + | + | + Transmitter $S_2$ leads to near-end crosstalk at receiver $E_2$. |
− | - | + | - Transmitter $S_3$ leads to near-end crosstalk at receiver $E_2$. |
− | + | + | + Near-end crosstalk is more unpleasant than far-end crosstalk. |
− | { | + | {Calculate the transmit power using the simplified assumption given. |
|type="{}"} | |type="{}"} | ||
$P_{\rm S} \ = \ $ { 1 3% } $\ \rm mW$ | $P_{\rm S} \ = \ $ { 1 3% } $\ \rm mW$ | ||
− | { | + | {What is the useful power arriving at the receiver? |
|type="{}"} | |type="{}"} | ||
$P_{\rm E} \ = \ $ { 0.88 3% } $\ \rm mW$ | $P_{\rm E} \ = \ $ { 0.88 3% } $\ \rm mW$ | ||
− | { | + | {Specify the power of the crosstalk interference. $ 1 \ \rm nW = 10^{-9} \ \rm W$ is valid. |
|type="{}"} | |type="{}"} | ||
$P_\text{NEXT} \ = \ $ { 0.186 3% } $\ \rm nW$ | $P_\text{NEXT} \ = \ $ { 0.186 3% } $\ \rm nW$ | ||
− | { | + | {What is the signal–to–crosstalk signal–to–noise ratio? |
|type="{}"} | |type="{}"} | ||
$\rm 10 \cdot \ lg\ {\it P}_E/{\it P}_\text{NEXT} \ = \ $ { 66.7 3% } $\ \rm dB$ | $\rm 10 \cdot \ lg\ {\it P}_E/{\it P}_\text{NEXT} \ = \ $ { 66.7 3% } $\ \rm dB$ | ||
Line 74: | Line 74: | ||
</quiz> | </quiz> | ||
− | === | + | ===Solution=== |
{{ML-Kopf}} | {{ML-Kopf}} | ||
− | '''(1)''' | + | '''(1)''' Crosstalk is caused by coupling of the transmitted signals to adjacent pairs of wires. |
− | * | + | *In the case of near–end crosstalk (NEXT), the interfering transmitter and the interfered receiver are at the same end of the line; in the case of far–end crosstalk (FEXT), they are at different ends. |
− | * | + | *However, since the interfering signals are also very strongly attenuated on the copper wire pair, NEXT is always by far the more dominant interfering effect compared with FEXT. |
− | + | <u>Solutions 2 and 4</u> are correct: | |
− | * | + | *Here, the receiver $E_2$ is particularly disturbed by its own transmitter $S_2$, i.e. by near–end crosstalk. |
− | * | + | *The interference of $E_2$ by $S_3$ is far–end crosstalk, while $S_1$ provides the useful signal for $E_2$. |
− | '''(2)''' | + | '''(2)''' The transmit power is equal to the integral over the power density spectrum: |
:$$P_{\rm S} = {\it\Phi}_{0} \cdot 2 f_0 = 5 \cdot 10^{-9}\, {\rm W}/{\rm Hz} \cdot 2 \cdot 10^{5}\,{\rm Hz}\hspace{0.15cm}\underline{ = 1\,{\rm mW}} | :$$P_{\rm S} = {\it\Phi}_{0} \cdot 2 f_0 = 5 \cdot 10^{-9}\, {\rm W}/{\rm Hz} \cdot 2 \cdot 10^{5}\,{\rm Hz}\hspace{0.15cm}\underline{ = 1\,{\rm mW}} | ||
\hspace{0.05cm}.$$ | \hspace{0.05cm}.$$ | ||
Line 93: | Line 93: | ||
− | '''(3)''' | + | '''(3)''' The following applies to the received power (excluding the component due to near–end crosstalk): |
:$$P_{\rm E} = \int_{-\infty}^{ | :$$P_{\rm E} = \int_{-\infty}^{ | ||
+\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm K}(f)|^2 | +\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm K}(f)|^2 | ||
Line 106: | Line 106: | ||
− | '''(4)''' | + | '''(4)''' For the interfering power component of the crosstalk interference one obtains |
:$$P_{\rm NEXT} = \int_{-\infty}^{ | :$$P_{\rm NEXT} = \int_{-\infty}^{ | ||
+\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm NEXT}(f)|^2 | +\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm NEXT}(f)|^2 | ||
Line 123: | Line 123: | ||
− | '''(5)''' | + | '''(5)''' ${P_{\rm E}}/{P_{\rm NEXT}} \approx 4.73 \cdot 10^{6}$ is valid, resulting in the logarithmic value of |
:$$10 \cdot {\rm lg}\hspace{0.15cm} {P_{\rm E}}/{P_{\rm NEXT}} = | :$$10 \cdot {\rm lg}\hspace{0.15cm} {P_{\rm E}}/{P_{\rm NEXT}} = | ||
10 \cdot {\rm lg}\hspace{0.15cm} | 10 \cdot {\rm lg}\hspace{0.15cm} |
Revision as of 12:54, 22 November 2021
On the $S_0$ bus at $\rm ISDN$ (Integrated Services Digital Networks), data is transmitted separately according to transmission direction on a four-wire line. The received signal of an ISDN device is therefore disturbed not only by connections on other wires but also by crosstalk from its own transmitted signal.
In this exercise, two ISDN terminals with $\text{50 m}$ distance are considered, assuming:
- For the power density spectrum (PDS) of the transmitter of each terminal, let ${\it\Phi}_{0} = 5 \cdot 10^{-9} \ \rm W/Hz$ be very simplified:
- $${\it\Phi}_{s}(f)= \left\{ \begin{array}{c} {\it\Phi}_{0} \\ 0 \end{array} \right. \begin{array}{c} {\rm{f\ddot{u}r}} \\ {\rm{f\ddot{u}r}} \end{array}\begin{array}{*{20}c} { |f| \le f_0 = 100\:{\rm kHz} \hspace{0.05cm},} \\ { |f| > f_0\hspace{0.05cm}.} \end{array}$$
- The power transfer function on the $S_0$ bus $\text{(0.6 mm}$ copper two–wire line, $\text{50 m)}$ is to be approximated in the considered range $0 < |f| < 100 \ \rm kHz$ as follows (very simplified) angenähert werden:
- $$|H_{\rm K}(f)|^2 = 0.9 - 0.04 \cdot \frac{|f|}{\rm 1 \ MHz}\hspace{0.05cm}.$$
- The near–end crosstalk power transfer function is given as follows $(\rm NEXT$ stands for near–end crosstalk$)$:
- $$|H_{\rm NEXT}(f)|^2 = \left ( K_{\rm NEXT} \cdot |f|\right )^{3/2}\hspace{0.05cm},\hspace{0.2cm}K_{\rm NEXT} = 6 \cdot 10^{-10}\,{\rm s} \hspace{0.05cm}.$$
The diagram shows the system configuration under consideration. Two twisted pairs connect subscribers $1$ and $2$ (one in each direction), while on two other twisted pairs (not in the same four-wire line) there is a connection between subscriber $3$ and subscriber $4$.
Notes:
- The exercise belongs to the chapter Properties of Balanced Copper Pairs.
- It also refers to the chapter ISDN Basic Access in the book "Examples of Communication Systems".
Questions
Solution
- In the case of near–end crosstalk (NEXT), the interfering transmitter and the interfered receiver are at the same end of the line; in the case of far–end crosstalk (FEXT), they are at different ends.
- However, since the interfering signals are also very strongly attenuated on the copper wire pair, NEXT is always by far the more dominant interfering effect compared with FEXT.
Solutions 2 and 4 are correct:
- Here, the receiver $E_2$ is particularly disturbed by its own transmitter $S_2$, i.e. by near–end crosstalk.
- The interference of $E_2$ by $S_3$ is far–end crosstalk, while $S_1$ provides the useful signal for $E_2$.
(2) The transmit power is equal to the integral over the power density spectrum:
- $$P_{\rm S} = {\it\Phi}_{0} \cdot 2 f_0 = 5 \cdot 10^{-9}\, {\rm W}/{\rm Hz} \cdot 2 \cdot 10^{5}\,{\rm Hz}\hspace{0.15cm}\underline{ = 1\,{\rm mW}} \hspace{0.05cm}.$$
(3) The following applies to the received power (excluding the component due to near–end crosstalk):
- $$P_{\rm E} = \int_{-\infty}^{ +\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm K}(f)|^2 \hspace{0.1cm}{\rm d}f = 2 {\it\Phi}_{0} \cdot \int_{0}^{ f_0} \left [ 0.9 - 0.04 \cdot \frac{f}{f_0} \right ] \hspace{0.1cm}{\rm d}f $$
- $$\Rightarrow \hspace{0.3cm}P_{\rm E} = 2 {\it\Phi}_{0} \cdot \left [ 0.9 \cdot f_0 - \frac{0.04}{2} \cdot \frac{f_0^2}{f_0} \right ] = 2 {\it\Phi}_{0} \cdot 0.88 = 0.88 \cdot P_{\rm S}\hspace{0.15cm}\underline{ = 0.88 \,{\rm mW}} \hspace{0.05cm}.$$
(4) For the interfering power component of the crosstalk interference one obtains
- $$P_{\rm NEXT} = \int_{-\infty}^{ +\infty} {\it\Phi}_{s}(f) \cdot |H_{\rm NEXT}(f)|^2 \hspace{0.1cm}{\rm d}f = 2 {\it\Phi}_{0} \cdot {K_{\rm NEXT}\hspace{0.01cm}}^{3/2} \cdot \int_{0}^{ f_0} f^{3/2} \hspace{0.1cm}{\rm d}f $$
- $$\Rightarrow \hspace{0.3cm} P_{\rm NEXT} = \frac{4}{5} \cdot {\it\Phi}_{0} \cdot {K_{\rm NEXT}\hspace{0.01cm}}^{3/2} \cdot f_0^{5/2} = 0.8 \cdot 5 \cdot 10^{-9}\, \frac{\rm W}{\rm Hz} \cdot \left ( 6 \cdot 10^{-10}\,{\rm s}\right )^{3/2} \cdot \left ( 10^{5}\,{\rm Hz}\right )^{5/2} = {0.186 \cdot 10^{-9}\,{\rm W}} \hspace{0.05cm} = \hspace{0.15cm}\underline{0.186 \,{\rm nW}} \hspace{0.05cm}.$$
(5) ${P_{\rm E}}/{P_{\rm NEXT}} \approx 4.73 \cdot 10^{6}$ is valid, resulting in the logarithmic value of
- $$10 \cdot {\rm lg}\hspace{0.15cm} {P_{\rm E}}/{P_{\rm NEXT}} = 10 \cdot {\rm lg}\hspace{0.15cm} (4.73 \cdot 10^{6}) \hspace{0.15cm}\underline{= 66.7\,\,{\rm dB}} \hspace{0.05cm}.$$