Difference between revisions of "Aufgaben:Exercise 2.10Z: Noise with DSB-AM and SSB-AM"

From LNTwww
m
m
 
Line 104: Line 104:
 
:$${\it \Phi}_\varepsilon(f) = \frac{2 \cdot N_0}{\alpha_{\rm K}^2} \hspace{0.3cm}  \Rightarrow \hspace{0.3cm} P_\varepsilon = \frac{4 \cdot N_0 \cdot B_{\rm NF}}{\alpha_{\rm K}^2}\hspace{0.05cm}.$$
 
:$${\it \Phi}_\varepsilon(f) = \frac{2 \cdot N_0}{\alpha_{\rm K}^2} \hspace{0.3cm}  \Rightarrow \hspace{0.3cm} P_\varepsilon = \frac{4 \cdot N_0 \cdot B_{\rm NF}}{\alpha_{\rm K}^2}\hspace{0.05cm}.$$
  
*This means:  When wittout carrier,  single-sideband modulation demonstrates the same noise behaviour as DSB-AM.
+
*This means:  When without carrier,  single-sideband modulation demonstrates the same noise behaviour as DSB-AM.
  
  

Latest revision as of 15:13, 9 April 2022

Shared block diagram for
DSB-AM and SSB-AM

Now the influence of noise on the sink-to-noise power ratio  $10 · \lg ρ_v$  for both  $\rm DSB–AM$  and  $\rm SSB–AM$ transmission  will be compared.   The illustration shows the underlying block diagram.


The differences between the two system variants are highlighted in red on the image, namely the modulator  (DSB or SSB)  as well as the dimensionless constant

$$ K = \left\{ \begin{array}{c} 2/\alpha_{\rm K} \\ 4/\alpha_{\rm K} \\ \end{array} \right.\quad \begin{array}{*{10}c} {\rm{for}} \\ {\rm{for}} \\ \end{array}\begin{array}{*{20}c} {\rm DSB} \hspace{0.05cm}, \\ {\rm SSB} \hspace{0.05cm} \\ \end{array}$$

of the receiver-side carrier signal  $z_{\rm E}(t) = K · \cos(ω_{\rm T} · t)$,  which is assumed to be frequency and phase synchronous with the carrier signal  $z(t)$  at the transmitter.


The system characteristics

  • frequency-independent channel transmission factor  $α_{\rm K}$,
  • transmission power  $P_{\rm S}$,
  • one–sided noise power density  $N_{\rm 0}$,
  • bandwidth  $B_{\rm NF}$  of the source signal,


captured by the shared performance parameter are labelled in green:

$$\xi = \frac{\alpha_{\rm K}^2 \cdot P_{\rm S}}{N_0 \cdot B_{\rm NF}}$$


Further note:

  • The cosine signal  $q(t)$  with frequency  $B_{\rm NF}$  stands for a source signal with bandwidth  $B_{\rm NF}$ composed of multiple frequencies.
  • The relationship between the transmission power  $P_{\rm S}$  and the power  $P_{q}$  of the source signal depends,  among other things,  on the modulation method.
  • "DSB–AM with carrier"  is parameterized by the modulation depth  $m = A_{\rm N}/A_{\rm T}$, 
    while  "SSB-AM"  is determined by the sideband-to-carrier ratio  $μ = A_{\rm N}/(2 · A_{\rm T})$.
  • The frequency-independent channel transmission factor  $α_{\rm K}$  is balanced by the constant  $K$,  so that in the noise-free case  $(N_0 = 0)$, 
    the sink signal  $v(t)$  matches the source signal  $q(t)$.
  • The sink SNR can thus be given as follows  $(T_0$ indicates the period of the source signal$)$:
$$ \rho_{v } = \frac{P_{q}}{P_{\varepsilon }}\hspace{0.5cm}{\rm with}\hspace{0.5cm} P_{q} = \frac{1}{T_{\rm 0}}\cdot\int_{0}^{ T_{\rm 0}} {q^2(t)}\hspace{0.1cm}{\rm d}t, \hspace{0.5cm}P_{\varepsilon} = \int_{-B_{\rm NF}}^{ +B_{\rm NF}} \hspace{-0.1cm}{\it \Phi_{\varepsilon}}(f)\hspace{0.1cm}{\rm d}f\hspace{0.05cm}.$$



Hints:


Questions

1

Which kind of demodulation is considered here?

Synchronous demodulation.
Envelope demodulation.

2

Which relationship holds between the quantities  $ρ_v$  and  $ξ$  for  double-sideband AM without carrier  $(m → ∞)$?

 $ρ_v = 2 · ξ$.
 $ρ_v = ξ$.
 $ρ_v = ξ/2$.

3

Which relationship holds between  $ρ_v$  and  $ξ$  for  single-sideband AM without carrier  as $(μ → ∞)$?

 $ρ_v = 2 · ξ$.
 $ρ_v = ξ$.
 $ρ_v = ξ/2$.

4

Let  $ξ = 10^4$.  Calculate the sink-to-noise ratio of   double-sideband AM  for modulation depths  $m = 0.5$  and  $m = 1$.

$m = 0.5\text{:} \ \ 10 · \lg \ ρ_v \ = \ $

$\ \rm dB$
$m = 1.0\text{:} \ \ 10 · \lg \ ρ_v \ = \ $

$\ \rm dB$

5

Further let  $ξ = 10^4$.  Calculate the sink-to-noise ratio of   single-sideband AM  for the parameters  $μ = 0.354$  and  $μ = 0.707$.

$μ = 0.354\text{:} \ \ \ 10 · \lg \ ρ_v \ = \ $

$\ \rm dB$
$μ = 0.707\text{:} \ \ \ 10 · \lg \ ρ_v \ = \ $

$\ \rm dB$


Solution

(1)  We are dealing with a   synchronous demodulatorAnswer 1  is correct.


(2)  Answer 2  is correct:

  • For DSB–AM without a carrier,   $P_{\rm S} = P_q/2$.  This is simultaneously the power of the useful component of the sink signal  $v(t)$.
  • The power-spectral density   ${\it Φ}_ε(f)$  of the   $v(t)$  noise component results from the convolution:
Noise power density
in double-sideband AM
Noise power density
in  upper-sideband AM
$${\it \Phi}_\varepsilon(f) = {\it \Phi}_{z{\rm E} }(f) \star {\it \Phi}_n (f) = \frac{1}{\alpha_{\rm K}^2} \cdot \big[\delta(f - f_{\rm T}) + \delta(f + f_{\rm T}) \big]\star {\it \Phi}_n (f) \hspace{0.05cm}.$$
  • The expression  $\big[$ ... $\big]$  describes the power-spectral density of a cosine signal with the signal amplitude   $K = 2$.
  • The correction of channel attenuation is considered with  $1/α_K^2$ .
  • Thus,  taking   ${\it \Phi}_n(f) = N_0/2$  into account,  we get:
$${\it \Phi}_\varepsilon(f) = \frac{N_0}{\alpha_{\rm K}^2} \hspace{0.3cm} \Rightarrow \hspace{0.3cm} P_\varepsilon = \int_{-B_{\rm NF}}^{+B_{\rm NF}} {{\it \Phi}_\varepsilon(f) }\hspace{0.1cm}{\rm d}f = \frac{2 \cdot N_0 \cdot B_{\rm NF}}{\alpha_{\rm K}^2}\hspace{0.05cm}.$$
  • From this,  it follows for the the signal-to-noise power ratio  $\rm (SNR)$:
$$\rho_{v } = \frac{P_{q}}{P_{\varepsilon }} = \frac{2 \cdot P_{\rm S}}{2 \cdot N_0 \cdot B_{\rm NF}/\alpha_{\rm K}^2} = \frac{\alpha_{\rm K}^2 \cdot P_{\rm S}}{N_0 \cdot B_{\rm NF}}\hspace{0.15cm}\underline { = \xi} \hspace{0.05cm}.$$


(3)  Answer 2  is correct:

  • In contrast to DSB,  $P_S = P_q/4$  holds for SSB,  as well as
$${\it \Phi}_\varepsilon(f) = {\it \Phi}_{z{\rm E} }(f) \star {\it \Phi}_n (f) = \frac{4}{\alpha_{\rm K}^2} \cdot \big[\delta(f - f_{\rm T}) + \delta(f + f_{\rm T}) \big]\star {\it \Phi}_n (f) \hspace{0.05cm}.$$
  • Taking   $B_{\rm HF} = B_{\rm NF}$  into account  (see adjacent diagram for USB modulation),  we now get:
$${\it \Phi}_\varepsilon(f) = \frac{2 \cdot N_0}{\alpha_{\rm K}^2} \hspace{0.3cm} \Rightarrow \hspace{0.3cm} P_\varepsilon = \frac{4 \cdot N_0 \cdot B_{\rm NF}}{\alpha_{\rm K}^2}\hspace{0.05cm}.$$
  • This means:  When without carrier,  single-sideband modulation demonstrates the same noise behaviour as DSB-AM.


(4)  Assuming a cosine carrier with amplitude  $A_{\rm T}$  and a similarly cosine source signal  $q(t)$,  we get for DSB with carrier:

$$ s(t) = \big (q(t) + A_{\rm T}\big ) \cdot \cos( \omega_{\rm T} \cdot t) = A_{\rm T} \cdot \cos( \omega_{\rm T} \cdot t) + \frac{A_{\rm N}}{2}\cdot \cos\big(( \omega_{\rm T}+ \omega_{\rm N}) \cdot t \big)+ \frac{A_{\rm N}}{2}\cdot \cos\big(( \omega_{\rm T}- \omega_{\rm N}) \cdot t\big)\hspace{0.05cm}.$$
  • The transmission power is thus given by
$$ P_{\rm S}= \frac{A_{\rm T}^2}{2} + 2 \cdot \frac{(A_{\rm N}/2)^2}{2} = \frac{A_{\rm T}^2}{2} + \frac{A_{\rm N}^2}{4} \hspace{0.05cm}.$$
  • Taking  $P_q = A_{\rm N}^2/2$  and  $m = A_{\rm N}/A_{\rm T}$  into account,  this can also be written as:
$$P_{\rm S}= \frac{A_{\rm N}^2}{4} \cdot \left[ 1 + \frac{2 \cdot A_{\rm T}^2}{A_{\rm N}^2}\right] = \frac{P_q}{2} \cdot \left[ 1 + {2 }/{m^2}\right]\hspace{0.05cm}.$$
  • With the noise power  $P_ε$  according to subtask  (2)  we thus obtain:
$$\rho_{v } = \frac{P_{q}}{P_{\varepsilon }} = \frac{2 \cdot P_{\rm S}\cdot (1 + 2/m^2)}{2 \cdot N_0 \cdot B_{\rm NF}/\alpha_{\rm K}^2} = \frac{\alpha_{\rm K}^2 \cdot P_{\rm S}}{N_0 \cdot B_{\rm NF}} \cdot \frac{1}{1 +{2 }/{m^2}} \hspace{0.05cm}.$$
  • And in logarithmic representation:
$$ 10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } = 10 \cdot {\rm lg} \hspace{0.15cm}\xi - 10 \cdot {\rm lg} \hspace{0.15cm}\left[{1 +{2 }/{m^2}}\right] \hspace{0.05cm}.$$
$$\Rightarrow \hspace{0.3cm}10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \ (m = 0.5) = 40 \,{\rm dB} - 10 \cdot {\rm lg} (9) \hspace{0.15cm}\underline {= 30.46\, {\rm dB}}$$
$$\Rightarrow \hspace{0.3cm}10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \ (m = 1.0) = 40 \,{\rm dB} - 10 \cdot {\rm lg} (3) \hspace{0.15cm}\underline {= 35.23\, {\rm dB} \hspace{0.05cm}}.$$


(5)  In  "SSB–AM"  there is only one sideband.

  • Therefore,  considering the sideband-to-carrier ratio   $μ = A_{\rm N}/(2A_{\rm T})$  gives:
$$ P_{\rm S}= \frac{A_{\rm T}^2}{2} + \frac{(A_{\rm N}/2)^2}{2} = {A_{\rm N}^2}/{8} \cdot \big[ 1 + {4 \cdot A_{\rm T}^2}/{A_{\rm N}^2}\big] = {P_q}/{4} \cdot \big[ 1 + {1 }/{\mu^2}\big] \hspace{0.05cm}.$$
  • Thus,  with the noise power from subtask  (3) we obtain:
$$\rho_{v } = \frac{P_{q}}{P_{\varepsilon }} = \frac{4 \cdot P_{\rm S}\cdot (1 + 1/\mu^2)}{4 \cdot N_0 \cdot B_{\rm NF}/\alpha_{\rm K}^2} = \frac{\alpha_{\rm K}^2 \cdot P_{\rm S}}{N_0 \cdot B_{\rm NF}} \cdot \frac{1}{1 +{1 }/{\mu^2}}\hspace{0.3cm} \Rightarrow \hspace{0.3cm}10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } = 10 \cdot {\rm lg} \hspace{0.15cm}\xi - 10 \cdot {\rm lg} \hspace{0.15cm}\big[{1 +{1 }/{\mu^2}}\big] \hspace{0.05cm}.$$
  • So we get the same result with SSB-AM as in DSB-AM with a modulation depth of  $m = \sqrt{2} · μ$.  From this,  it further follows:
$$10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \hspace{0.15cm}({\rm SSB,} \hspace{0.1cm}\mu = {0.5}/{\sqrt{2}}) = 10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \hspace{0.15cm}({\rm DSB,} \hspace{0.1cm}m=0.5) \hspace{0.15cm}\underline {=30.46\,{\rm dB}},$$
$$10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \hspace{0.15cm}({\rm SSB,} \hspace{0.1cm}\mu = {1.0}/{\sqrt{2}}) = 10 \cdot {\rm lg} \hspace{0.15cm}\rho_{v } \hspace{0.15cm}({\rm DSB,} \hspace{0.1cm}m=1.0) \hspace{0.15cm}\underline {=35.23\,{\rm dB}}\hspace{0.05cm}.$$