Exercise 5.1: Sampling Theorem

From LNTwww
Revision as of 13:47, 13 May 2021 by Guenter (talk | contribs)

Sampling of an analog signal  $x(t)$

Given is an analog signal  $x(t)$  according to the sketch:

  • It is known that this signal does not contain any frequencies higher than  $B_{\rm NF} = 4 \ \text{kHz}$.
  • By sampling with the sampling rate  $f_{\rm A}$ , the signal  $x_{\rm A}(t)$ sketched in red in the diagram is obtained.
  • For signal reconstruction a low-pass filter is used, for whose frequency response applies:
$$H(f) = \left\{ \begin{array}{c} 1 \\ 0 \\ \end{array} \right.\quad \begin{array}{*{5}c} {\rm{{\rm{f\ddot{u}r}}}} \\ {\rm{{\rm{f\ddot{u}r}}}} \\ \end{array}\begin{array}{*{5}c} |f| < f_1 \hspace{0.05cm}, \\ |f| > f_2 \hspace{0.05cm} \\ \end{array}$$

The range between the frequencies  $f_1$  and  $f_2 > f_1$  is not relevant for the solution of this task.

The corner frequencies  $f_1$  and  $f_2$  are to be determined in such a way that the output signal  $y(t)$  of the low-pass filter exactly matches the signal  $x(t)$ .





Hints:


Questions

1

Determine the underlying sampling rate from the graph.

$f_{\rm A}\ = \ $

 $\text{kHz}$

2

At which frequencies does the spectral function  $X_{\rm A}(f)$  have no components with certainty?

$f = 2.5 \ \text{kHz},$
$f= 5.5 \ \text{kHz},$
$f= 6.5 \ \text{kHz},$
$f= 34.5 \ \text{kHz}.$

3

What is the minimum size of the lower cut-off frequency  $f_1$  that the signal is perfectly reconstructed?

$f_{1,\ \text{min}}\ = \ $

 $\text{kHz}$

4

What is the maximum size of the upper corner frequency  $f_2$  that the signal is perfectly reconstructed?

$f_{2,\ \text{max}}\ = \ $

 $\text{kHz}$


Solution

(1)  The distance between two adjacent samples is  $T_{\rm A} = 0.1 \ \text{ms}$.  Thus, for the sampling rate  $f_{\rm A} = 1/ T_{\rm A} \;\underline {= 10 \ \text{kHz}}$is obtained.


Spectrum  $X_{\rm A}(f)$  of the sampled signal
(schematic representation)

(2)  Proposed solutions 2 and 4 are correct:

  • The spectrum  $X_{\rm A}(f)$  of the sampled signal is obtained from  $X(f)$  by periodic continuation at a distance of  $f_{\rm A} = 10 \ \text{kHz}$.
  • From the sketch you can see that  $X_{\rm A}(f)$  can have signal parts at  $f = 2.5 \ \text{kHz}$  and  $f = 6.5 \ \text{kHz}$;.
  • In contrast, there are no components at  $f = 5.5 \ \text{kHz}$.
  • Also at  $f = 34.5 \ \text{kHz}$  will be valid  $X_{\rm A}(f) = 0$.


(3)  It must be ensured that all frequencies of the analog signal are weighted with  $H(f) = 1$.

  • From this follows according to the sketch:
$$f_{1, \ \text{min}} = B_{\rm NF} \;\underline{= 4 \ \text{kHz}}.$$


(4)  Likewise, it must be guaranteed that all spectral components of  $X_{\rm A}(f)$, that are not contained in  $X(f)$  are removed by the low-pass filter.

  • According to the sketch, the following must apply:
$$f_{2, \ \text{max}} = f_{\rm A} – B_{\rm NF} \;\underline{= 6 \ \text{kHz}}.$$