Difference between revisions of "Linear and Time Invariant Systems/Classification of the Distortions"

From LNTwww
(17 intermediate revisions by 3 users not shown)
Line 1: Line 1:
  
 
{{Header|
 
{{Header|
Untermenü=Signalverzerrungen und Entzerrung
+
Untermenü=Signal Distortion and Equalization
|Vorherige Seite=Einige systemtheoretische Tiefpassfunktionen
+
|Vorherige Seite=Some_Low-Pass_Functions_in_Systems_Theory
|Nächste Seite=Nichtlineare Verzerrungen
+
|Nächste Seite=Nonlinear_Distortions
 
}}
 
}}
  
Line 10: Line 10:
 
{{BlaueBox|TEXT=   
 
{{BlaueBox|TEXT=   
 
$\text{Definition:}$   
 
$\text{Definition:}$   
Generally, undesirable deterministic changes of a message signal by a transmission system are considered as  '''distortions''' . }}
+
In general,  $\text{distortion}$  is understood to be undesirable deterministic changes in a message signal caused by a transmission system. }}
  
  
In addition to stochastic interferences (noise, crosstalk, etc.), such deterministic distortions are a critical limitation on transmission quality and rate for many messaging systems.
+
In addition to stochastic interferences  (noise, crosstalk, etc.), such deterministic distortions are a critical limitation on the transmission quality and rate for many communication systems.
  
 
This chapter presents these distortions in a summarising way, in particular:
 
This chapter presents these distortions in a summarising way, in particular:
  
*the quantitative detection of such signal falsifications via the distortion power,
+
*The quantitative detection of such signal falsifications via the distortion power,
 
*the distinguishing features between nonlinear and linear distortions,
 
*the distinguishing features between nonlinear and linear distortions,
*the meaning and computation of the distortion factor in nonlinear systems and
+
*the meaning and computation of the distortion factor in nonlinear systems,  and
*the effects of linear distortions of damping and phase distortions.
+
*the effects of linear damping and phase distortions.
  
  
Further information on the topic of "distortions" as well as tasks, simulations and programming exercises can be found in
 
*Chapter 6: Linear Time-Invariant Systems (Programme lzi)
 
  
 
+
==Prerequisites for the second main chapter==
of the practical course "Simulation Methods in Communications Engineering". This (former) LNT course at TU Munich is based on
 
*the educational software package  [http://www.lntwww.de/downloads/Sonstiges/Programme/LNTsim.zip LNTsim]   ⇒   Link refers to the ZIP-version of the programme, and
 
*this practical course guide  [http://www.lntwww.de/downloads/Sonstiges/Texte/Praktikum_LNTsim_Teil_A.pdf Praktikumsanleitung]    ⇒   Link refers to the PDF-version; Chapter 6: pages 99-118.
 
 
 
 
 
==Prerequisites for the Entire Second Main Chapter==
 
 
<br>
 
<br>
In the following, we consider a system whose input is the signal &nbsp;$x(t)$&nbsp; with the corresponding spectrum &nbsp;$X(f)$&nbsp;. The output signal is denoted by &nbsp;$y(t)$&nbsp; and its spectrum by &nbsp;$Y(f).$
 
 
 
[[File:P_ID873__LZI_T_2_1_S1_neu.png|frame| Description of a linear system|class=fit]]
 
[[File:P_ID873__LZI_T_2_1_S1_neu.png|frame| Description of a linear system|class=fit]]
  
The block labelled "system" can be a part of an electrical circuit or a complete transmission system consisting of transmitter, channel and receiver.  
+
In the following, we consider a system whose input is the signal &nbsp;$x(t)$&nbsp; with the corresponding spectrum &nbsp;$X(f)$.&nbsp; The output signal is denoted by &nbsp;$y(t)$&nbsp; and its spectrum by &nbsp;$Y(f).$
  
 
+
The block labelled&nbsp; "system"&nbsp; can be a part of an electrical circuit or a complete communicarion system consisting of transmitter, channel and receiver.
For the whole main chapter &rdquo;Signal Distortions and Equalisation&rdquo; the following shall apply:  
+
<br clear=all>
*The system be&nbsp;'''time-invariant'''. If the input signal &nbsp;$x(t)$&nbsp; results in the output signal &nbsp;$y(t)$, then a later input signal of the same form &ndash; in particular &nbsp;$x(t - t_0)$&nbsp; &ndash; will result in the signal &nbsp;$y(t - t_0)$&nbsp;.  
+
For the whole main chapter&nbsp; "Signal Distortions and Equalization"&nbsp; the following shall apply:  
*&nbsp;'''No noise'''&nbsp; is considered, which is always present in real systems.&nbsp; For the description of these phenomena we refer to the&nbsp; $\rm LNTwww$&ndash;book&nbsp; [[Stochastische Signaltheorie]].  
+
*The system be&nbsp;'''time-invariant'''.&nbsp; If the input signal &nbsp;$x(t)$&nbsp; results in the output signal &nbsp;$y(t)$, then a later input signal of the same form &ndash; in particular &nbsp;$x(t - t_0)$&nbsp; &ndash; will result in the signal &nbsp;$y(t - t_0)$.  
*&nbsp;'''No detailed knowledge'''&nbsp; about the system is assumed.&nbsp; In the following, all system properties are derived from the signals  &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; or their spectra alone.  
+
*In the following,&nbsp; '''no noise'''&nbsp; is considered, which is always present in real systems.&nbsp; For the description of these phenomena we refer to the book&nbsp; [[Theory_of_Stochastic_Signals|Theory of Stochastic Signals]].  
*In particular, no specifications are given with regards to&nbsp; '''linearity''' for the time being.&nbsp; The "system" can be linear (prerequisite for the application of the superposition principle) or non-linear.  
+
*About the system &nbsp;'''no detailed knowledge'''&nbsp; is assumed.&nbsp; In the following, all system properties are derived from the signals  &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; or their spectra alone.  
 +
*In particular, no specifications are made for the time being with regard to&nbsp; '''linearity'''.&nbsp; The "system" can be linear (prerequisite for the application of the superposition principle) or non-linear.  
 
*Not all system properties are discernible from a single test signal &nbsp;$x(t)$&nbsp; and its response &nbsp;$y(t)$&nbsp;. Therefore, &nbsp;'''sufficiently many test signals'''&nbsp; must be used for evaluation.  
 
*Not all system properties are discernible from a single test signal &nbsp;$x(t)$&nbsp; and its response &nbsp;$y(t)$&nbsp;. Therefore, &nbsp;'''sufficiently many test signals'''&nbsp; must be used for evaluation.  
  
  
In the following, we will classify transmission systems in more detail in this respect.  
+
In the following, we will classify communication systems in more detail in this respect.  
  
==Ideal and Distortion-free System==
+
==Ideal and distortion-free system==
 
<br>
 
<br>
 
{{BlaueBox|TEXT=   
 
{{BlaueBox|TEXT=   
 
$\text{Definition:}$&nbsp;  
 
$\text{Definition:}$&nbsp;  
One deals with an&nbsp; '''ideal system''' if the output signal &nbsp;$y(t)$&nbsp; is exactly equal to the input signal &nbsp;$x(t)$&nbsp;:
+
One deals with an&nbsp; '''ideal system'''&nbsp; if the output signal &nbsp;$y(t)$&nbsp; is identical with the input signal &nbsp;$x(t)$:
 
:$$y(t) \equiv x(t).$$}}
 
:$$y(t) \equiv x(t).$$}}
  
  
It should be noted that such an ideal system does not exist in reality even if statistical disturbances and noise processes, that always exist but are not considered in this book, are disregarded. Every transmission medium exhibits losses (damping) and transit times. Even if these physical phenomena are very small, they are never zero. It is therefore necessary to introduce a somewhat less strict quality characteristic.  
+
*It should be noted that such an ideal system does not exist in reality even if statistical disturbances and noise processes (that always exist but are not considered in this bookare disregarded.&nbsp;
 +
*Every transmission medium exhibits losses&nbsp; (damping)&nbsp; and transit times.&nbsp; Even if these physical phenomena are very small, they are never zero.&nbsp; Therefore  it is necessary to introduce a somewhat less strict quality characteristic.  
 +
 
  
 
{{BlaueBox|TEXT=   
 
{{BlaueBox|TEXT=   
Line 65: Line 58:
 
A&nbsp; '''distortion-free system'''&nbsp; exists if the following condition is fulfilled:
 
A&nbsp; '''distortion-free system'''&nbsp; exists if the following condition is fulfilled:
 
:$$y(t) = \alpha \cdot x(t - \tau).$$
 
:$$y(t) = \alpha \cdot x(t - \tau).$$
Here, &nbsp;$α$&nbsp; describes the damping factor and &nbsp;$τ$&nbsp; the transit time.}}
+
*Here, &nbsp;$α$&nbsp; describes the damping factor and &nbsp;$τ$&nbsp; the transit time.
 +
*If this condition is not met, the system is said to be&nbsp; ''' distortive'''.}}  
  
 
If this condition is not met, the system is said to be distortive.
 
  
 
{{GraueBox|TEXT=   
 
{{GraueBox|TEXT=   
Line 78: Line 70:
 
Note:  
 
Note:  
 
*The damping factor &nbsp;$α$&nbsp; can be completely reversed by a receiver-side gain of &nbsp;$1/α = 1.25$, but it must be taken into account that this also increases any noise.  
 
*The damping factor &nbsp;$α$&nbsp; can be completely reversed by a receiver-side gain of &nbsp;$1/α = 1.25$, but it must be taken into account that this also increases any noise.  
*However, the transit time &nbsp;$τ$&nbsp; cannot be compensated due to&nbsp; [[Signal_Representation/Signal_classification#Kausale_und_akausale_Signale|Kausalitätsgründen]]&nbsp;.&nbsp; It now depends on the application whether such a transit time is subjectively perceived as disturbing or not. }}
+
*However, the transit time &nbsp;$τ$&nbsp; cannot be compensated due to&nbsp; [[Signal_Representation/Signal_classification#Causal_and_Non-Causal_Signals|causality reasons]].&nbsp; It now depends on the application whether such a transit time is subjectively perceived as disturbing or not. }}
  
  
For example, even with a transit time of one second the (unidirectional) TV broadcast of an event is still described as "live".&nbsp; In contrast to this, transit times of&nbsp; $\text{300 ms}$&nbsp; are already perceived as very disturbing in bidirectional communication – for example, a telephone call. You either wait for the other person to react or both participants interrupt each other.
+
*For example, even with a transit time of one second the&nbsp; (unidirectional)&nbsp; TV broadcast of an event is still described as "live".&nbsp;  
 +
*In contrast to this, transit times of&nbsp; $\text{300 ms}$&nbsp; are already perceived as very disturbing in bidirectional communication – e.g. a telephone call.&nbsp; You either wait for the other person to react or both participants interrupt each other.
  
==Quantitative Measure of Signal Distortion==
+
==Quantitative measure for the signal distortions==
 
<br>
 
<br>
We now consider a distortive system on the basis of the input and output signal.&nbsp; In doing so, we assume that apart from the signal distortions there is no additional damping factor &nbsp; $α$&nbsp; which is constant for all frequencies and no additional transit time&nbsp; $τ$&nbsp; that is constant for all frequencies. These conditions are fulfilled for the signal sections sketched below.
+
[[File:P_ID875__LZI_T_2_1_S3_neu.png|right|frame|Input and output of a distortive system and error signal (below)|class=fit]]
  
[[File:P_ID875__LZI_T_2_1_S3_neu.png|right|frame|Input and output of a distortive system and error signal (below)|class=fit]]
+
We now consider a distortive system on the basis of the input and output signal.&nbsp;
 +
*In doing so, we assume that apart from the signal distortions there is no additional damping factor &nbsp; $α$&nbsp; which is constant for all frequencies and no additional transit time&nbsp; $τ$&nbsp; that is constant for all frequencies.
 +
*These conditions are fulfilled for the signal sections sketched on the right.
  
In addition to the signals &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp;, the difference signal is also shown in the diagram:
+
*In addition to the signals &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp;, the difference signal is shown in the diagram:
 
:$$\varepsilon(t) = y(t) - x(t).$$
 
:$$\varepsilon(t) = y(t) - x(t).$$
 
As a quantitative measure of the strength of distortions, for example, the&nbsp; '''squared mean of this difference signal''' is applicable:
 
As a quantitative measure of the strength of distortions, for example, the&nbsp; '''squared mean of this difference signal''' is applicable:
 
:$$\overline{\varepsilon^2(t)} = \frac{1}{T_{\rm M}} \cdot \int_{ 0 }^{ T_{\rm M}} {\varepsilon^2(t) }\hspace{0.1cm}{\rm d}t\hspace{0.4cm}  \left( = P_{\rm V} \right).$$
 
:$$\overline{\varepsilon^2(t)} = \frac{1}{T_{\rm M}} \cdot \int_{ 0 }^{ T_{\rm M}} {\varepsilon^2(t) }\hspace{0.1cm}{\rm d}t\hspace{0.4cm}  \left( = P_{\rm V} \right).$$
<br clear=all>
+
 
 
The following should be noted about this equation:  
 
The following should be noted about this equation:  
*The measurement time&nbsp; $T_{\rm M}$&nbsp; must be chosen sufficiently large.&nbsp; Actually, this equation should be formulated as a limit process.  
+
*The measuring time&nbsp; $T_{\rm M}$&nbsp; must be chosen sufficiently large.&nbsp; Actually, this equation should be formulated as a limit process.  
*The squared mean mentioned above is often also called ''mean squared error''&nbsp; $\rm (MSE)$&nbsp; or &nbsp; '''distortion power'''&nbsp; $P_{\rm D}$&nbsp;.  
+
*The squared mean mentioned above is called&nbsp; "mean squared error"&nbsp; $\rm (MSE)$&nbsp; or &nbsp; '''distortion power'''&nbsp; $P_{\rm V}$&nbsp; $($because of&nbsp; "distortion" &nbsp; &rArr; &nbsp; German:&nbsp; "Verzerrung" &nbsp; &rArr; &nbsp; $\rm V)$.
*If &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; are voltage signals, then &nbsp;$P_{\rm D}$&nbsp; has the unit of &nbsp;${\rm V}^2$, meaning the power is related to the resistance &nbsp;$R = 1 \ Ω$&nbsp; according to the above definition.  
+
*If &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; are voltage signals, then &nbsp;$P_{\rm V}$&nbsp; has the unit of &nbsp;${\rm V}^2$, meaning the power is related to the resistance &nbsp;$R = 1 \ Ω$&nbsp; according to the above definition.  
  
  
 
{{BlaueBox|TEXT=   
 
{{BlaueBox|TEXT=   
$\text{Definition:}$&nbsp; Making use of the power &nbsp;(based on &nbsp;$R = 1 \ Ω$&nbsp;)&nbsp; &nbsp;$P_x$&nbsp; of the input signal &nbsp;$x(t)$&nbsp; the &nbsp;'''signal–to–distortion (power) ratio'''&nbsp; can be given as:
+
$\text{Definition:}$&nbsp; Making use of the power&nbsp; $P_x$&nbsp; &nbsp;$($based on &nbsp;$R = 1 \ Ω)$&nbsp; of the input signal &nbsp;$x(t)$&nbsp; the &nbsp; $\text{signal–to–distortion (power) ratio}$&nbsp; can be given as:
:$$\rho_{\rm D} = \frac{ P_{x} }{P_{\rm D} } \hspace{0.3cm} \Rightarrow \hspace{0.3cm}  10 \cdot \lg \hspace{0.1cm}\rho_{\rm D} =
+
:$$\rho_{\rm V} = \frac{ P_{x} }{P_{\rm V} } \hspace{0.3cm} \Rightarrow \hspace{0.3cm}  10 \cdot \lg \hspace{0.1cm}\rho_{\rm V} =
  10 \cdot \lg \hspace{0.1cm}\frac{ P_{x} }{P_{\rm D} }\hspace{0.3cm}  \left( {\rm in \hspace{0.15cm} dB} \right).$$
+
  10 \cdot \lg \hspace{0.1cm}\frac{ P_{x} }{P_{\rm V} }\hspace{0.3cm}  \left( {\rm in \hspace{0.15cm} dB} \right).$$
  
For the signals shown in the diagram above &nbsp;$P_x = 4  \ {\rm V}^2$, &nbsp;$P_{\rm D} = 0.04  \ {\rm V}^2$&nbsp; and thus &nbsp;$10 \cdot {\rm  lg} \ ρ_{\rm D} = 20 \ \rm dB$ hold.}}
+
For the signals shown in the diagram above &nbsp;$P_x = 4  \ {\rm V}^2$, &nbsp;$P_{\rm V} = 0.04  \ {\rm V}^2$&nbsp; and thus &nbsp;$10 \cdot {\rm  lg} \ ρ_{\rm V} = 20 \ \rm dB$ hold.}}
  
  
We reference the interactive applet &nbsp;[[Applets:Lineare_Verzerrungen_periodischer_Signale|Lineare Verzerrungen periodischer Signale]].
+
We reference the interactive applet &nbsp;[[Applets:Linear_Distortions_of_Periodic_Signals|Linear Distortions of Periodic Signals]].
  
==Significance of Damping and Transit Time==
+
==Elimination of damping factor and transit time==
 
<br>
 
<br>
The equations given on the last page do not result in applicable statements if the system is additionanlly affected by an attenuation &nbsp;$α$&nbsp; and/or transit time &nbsp;$τ$&nbsp;&nbsp;. The diagram shows the attenuated, delayed and distorted signal
+
The equations given on the last page do not result in applicable statements if the system is additionanlly affected by an attenuation factor &nbsp;$α$&nbsp; and/or a transit time &nbsp;$τ$.&nbsp; The diagram shows the attenuated, delayed and distorted signal
  
[[File:P_ID876__LZI_T_2_1_S4_neu.png|right|frame|Significance of damping and transit time|class=fit]]
+
[[File:P_ID876__LZI_T_2_1_S4_neu.png|right|frame|Elimination of damping factor&nbsp;$α$&nbsp;
 +
<br>and transit time&nbsp; $τ$|class=fit]]
  
 
:$$y(t) = \alpha \cdot x(t - \tau) + \varepsilon_1(t).$$
 
:$$y(t) = \alpha \cdot x(t - \tau) + \varepsilon_1(t).$$
 
The term &nbsp;$ε_1(t)$&nbsp; summarises all distortions.&nbsp; It can be seen from the green area that the error signal &nbsp;$ε_1(t)$&nbsp; is relatively small.  
 
The term &nbsp;$ε_1(t)$&nbsp; summarises all distortions.&nbsp; It can be seen from the green area that the error signal &nbsp;$ε_1(t)$&nbsp; is relatively small.  
  
In contrast to this, if the attenuation &nbsp;$α$&nbsp; and transit time &nbsp;$τ$&nbsp; are unknwon, the following should be noted:  
+
In contrast to this, if the attenuation factor  &nbsp;$α$&nbsp; and the transit time &nbsp;$τ$&nbsp; are unknwon, the following should be noted:  
*The error signal &nbsp;$ε_2(t) = y(t) - x(t)$&nbsp; determined in this way is relatively large despite small distortions &nbsp;$ε_1(t)$&nbsp;.  
+
*The error signal &nbsp;$ε_2(t) = y(t) - x(t)$&nbsp; determined in this way is relatively large despite small distortions &nbsp;$ε_1(t)$.  
 
*Here, instead of the distortion power the distortion energy must be considered because &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; are energy-limited signals.  
 
*Here, instead of the distortion power the distortion energy must be considered because &nbsp;$x(t)$&nbsp; and &nbsp;$y(t)$&nbsp; are energy-limited signals.  
 
*The distortion energy is obtained by varying the unknown quantities &nbsp;$α$&nbsp; and &nbsp;$τ$&nbsp; and thus finding the minimum of the mean squared error:
 
*The distortion energy is obtained by varying the unknown quantities &nbsp;$α$&nbsp; and &nbsp;$τ$&nbsp; and thus finding the minimum of the mean squared error:
:$$E_{\rm D}  = \min_{\alpha, \ \tau} \int_{ - \infty }^{ + \infty}
+
:$$E_{\rm V}  = \min_{\alpha, \ \tau} \int_{ - \infty }^{ + \infty}
 
  {\big[y(t) - \left(\alpha \cdot x(t - \tau) \right) \big]^2}\hspace{0.1cm}{\rm d}t.$$
 
  {\big[y(t) - \left(\alpha \cdot x(t - \tau) \right) \big]^2}\hspace{0.1cm}{\rm d}t.$$
*The energy of the damped and delayed signal &nbsp;$α · x(t - τ)$&nbsp; is equal to &nbsp;$α^2 · E_x$ independent of the transit time &nbsp;$τ$&nbsp;. Thus for the signal-to-distortion (power) ratio the following is applicable:
+
*The energy of the damped and delayed signal &nbsp;$α · x(t - τ)$&nbsp; is &nbsp;$E_{\rm V}  =α^2 · E_x$ independent of the transit time &nbsp;$τ$.&nbsp;  Thus for the signal-to-distortion (power) ratio the following is applicable:
:$$\rho_{\rm D} = \frac{ \alpha^2 \cdot E_{x}}{E_{\rm D}}\hspace{0.3cm}{\rm or}\hspace{0.3cm}\rho_{\rm D}= \frac{ \alpha^2 \cdot P_{x}}{P_{\rm D}} .$$
+
:$$\rho_{\rm V} = \frac{ \alpha^2 \cdot E_{x}}{E_{\rm V}}\hspace{0.3cm}{\rm or}\hspace{0.3cm}\rho_{\rm D}= \frac{ \alpha^2 \cdot P_{x}}{P_{\rm V}} .$$
*The first of these two equations applies to time-limited and thus energy-limited signals, the second one to time-unlimited and thus power-limited signals according to the page &nbsp;[[Signal_Representation/Signal_classification#Energiebegrenzte_und_leistungsbegrenzte_Signale|Energiebegrenzte und leistungsbegrenzte Signale]]&nbsp; in the book &rdquo;Signal Representation&rdquo;.
+
*The first of these two equations applies to time-limited and thus energy-limited signals, the second one to time-unlimited and thus power-limited signals according to the page &nbsp;[[Signal_Representation/Signal_classification#Energy.E2.80.93Limited_and_Power.E2.80.93Limited_Signals|Energy-limited and power-limited signals]]&nbsp; in the book "Signal Representation".
  
==Linear and Nonlinear Distortions==
+
==Linear and non-linear distortions==
 
<br>
 
<br>
 
A distinction is made between linear and nonlinear distortions:  
 
A distinction is made between linear and nonlinear distortions:  
  
If the system is linear and time-invariant&nbsp; $(\rm LTI)$, then it is fully characterised by its&nbsp; [[Linear_and_Time_Invariant_Systems/Systembeschreibung_im_Frequenzbereich#.C3.9Cbertragungsfunktion_-_Frequenzgang|Frequenzgang]]&nbsp; $H(f)$ and the following can be stated:  
+
If the system is linear and time-invariant&nbsp; $(\rm LTI)$, then it is fully characterised by its&nbsp; [[Linear_and_Time_Invariant_Systems/System_Description_in_Frequency_Domain#Frequency_response_.E2.80.93_Transfer_function|frequency response]]&nbsp; $H(f)$ and the following can be stated:  
*According to the&nbsp; $H(f)$&ndash;definition the following holds for the output spectrum: &nbsp; $Y(f)=X(f) · H(f)$. &nbsp; As a consequence according to the calculation rules of multiplication, &nbsp;$Y(f)$&nbsp; cannot contain any frequency components that are not already contained in &nbsp;$X(f)$&nbsp;.  
+
*According to the&nbsp; $H(f)$&nbsp; definition the following holds for the output spectrum: &nbsp; $Y(f)=X(f) · H(f)$. &nbsp; As a consequence according to the calculation rules of multiplication, &nbsp;$Y(f)$&nbsp; cannot contain any frequency components that are not already contained in &nbsp;$X(f)$&nbsp;.  
*The inverse implies: &nbsp; The output signal &nbsp;$y(t)$&nbsp; can include any frequency &nbsp;$f_0$&nbsp; already contained in the input signal &nbsp;$x(t)$&nbsp;. The prerequisite is therefore that &nbsp;$X(f_0) ≠ 0$&nbsp; holds.  
+
*The inverse implies: &nbsp; The output signal &nbsp;$y(t)$&nbsp; can include any frequency &nbsp;$f_0$&nbsp; already contained in the input &nbsp;$x(t)$&nbsp;. The prerequisite is therefore that &nbsp;$X(f_0) ≠ 0$&nbsp; holds.  
*For an LTI-system the absolute bandwidth &nbsp;$(B_y)$&nbsp; of the output signal is never greater than the bandwidth &nbsp;$(B_x)$&nbsp; of the input signal: &nbsp; $B_y \le B_x .$
+
*For an LTI system the absolute bandwidth &nbsp;$B_y$&nbsp; of the output signal is never greater than the bandwidth &nbsp;$B_x$&nbsp; of the input signal: &nbsp; $B_y \le B_x .$
  
  
Line 144: Line 140:
  
 
[[File:EN_LZI_T_2_1_S5_neu.png|frame| Linear and nonlinear distortions|class=fit]]
 
[[File:EN_LZI_T_2_1_S5_neu.png|frame| Linear and nonlinear distortions|class=fit]]
*In the above diagram&nbsp; $B_y = B_x$&nbsp; holds. Es liegen&nbsp; '''linear distortions'''&nbsp; vor, da sich in diesem Frequenzband&nbsp; $X(f)$&nbsp; und&nbsp; $Y(f)$&nbsp; unterscheiden.  
+
In the upper diagram&nbsp; $B_y = B_x$&nbsp; holds. There are&nbsp; '''linear distortions'''&nbsp; because in this frequency band&nbsp; $X(f)$&nbsp; and&nbsp; $Y(f)$&nbsp; differ.
*Eine Bandbegrenzung&nbsp; $(B_y < B_x)$&nbsp; ist eine Sonderform linearer Verzerrungen, die im&nbsp; [[Linear_and_Time_Invariant_Systems/Lineare_Verzerrungen|übernächsten Kapitel]]&nbsp;  behandelt werden.
+
 +
A band limitation&nbsp; $(B_y < B_x)$&nbsp; is a special form of linear distortion, which will be discussed in the&nbsp; [[Linear_and_Time_Invariant_Systems/Lineare_Verzerrungen|chapter after next]].
 +
 
  
  
  
 +
The lower diagram shows an example of&nbsp; '''non-linear distortions'''&nbsp; $(B_y > B_x)$.&nbsp; For such a system no frequency response&nbsp; $H(f)$&nbsp; can be given.
  
*Die untere Grafik zeigt ein Beispiel für&nbsp; '''nonlinear distortions'''&nbsp; $(B_y > B_x)$.&nbsp; Für ein solches System kann kein Frequenzgang&nbsp; $H(f)$&nbsp; angegeben werden.
+
Descriptive quantities applicable for non-linear systems will be explained in the next chapter&nbsp; [[Linear_and_Time_Invariant_Systems/Nichtlineare_Verzerrungen|Non-linear Distortions]]&nbsp;.  
*Welche Beschreibungsgrößen für nichtlineare Systeme geeignet sind, wird im nächsten Kapitel&nbsp; [[Linear_and_Time_Invariant_Systems/Nichtlineare_Verzerrungen|Nichtlineare Verzerrungen]]&nbsp; dargelegt.  
 
 
<br clear=all>
 
<br clear=all>
Bei den meisten realen Übertragungskanälen treten sowohl lineare als auch nichtlineare Verzerrungen auf.&nbsp; Für eine ganze Reihe von Problemstellungen ist jedoch die klare Trennung der beiden Verzerrungsarten essentiell.&nbsp; In&nbsp; [Kam04]<ref>Kammeyer, K.D.: ''Nachrichtenübertragung''. Stuttgart: B.G. Teubner, 4. Auflage, 2004.</ref>&nbsp;  wird ein entsprechendes Ersatzmodell angegeben. }}
+
In most real transmission channels both linear and non-linear distortions occur.&nbsp; However, for a whole range of problems the precise separation of the two types of distortions is essential.&nbsp; In&nbsp; [Kam04]<ref>Kammeyer, K.D.:&nbsp; Nachrichtenübertragung.&nbsp; Stuttgart: B.G. Teubner, 4. Auflage, 2004.</ref>&nbsp;  a corresponding substitute model is shown. }}
  
  
We refer here to the learning video &nbsp;[[Lineare_und_nichtlineare_Verzerrungen_(Lernvideo)|Lineare und nichtlineare Verzerrungen]]&nbsp;.
+
We refer here to the&nbsp; (German language)&nbsp; learning video &nbsp;[[Lineare_und_nichtlineare_Verzerrungen_(Lernvideo)|Linear and non-Linear distortions]].
  
==Exercises for the Chapter==
+
==Exercises for the chapter==
  
[[Aufgaben:2.1_Linear%3F_-_Nichtlinear%3F| Aufgabe 2.1: Linear? - Nichtlinear?]]
+
[[Aufgaben:Exercise_2.1:_Linear%3F_Or_Non-Linear%3F| Exercise 2.1: Linear? Or Non-Linear?]]
  
[[Aufgaben:2.1Z_Verzerrung_und_Entzerrung|Aufgabe 2.1Z: Verzerrung und Entzerrung]]
+
[[Aufgaben:Exercise_2.1Z:_Distortion_and_Equalisation|Exercise 2.1Z: Distortion and Equalisation]]
  
[[Aufgaben:2.2_Verzerrungsleistung|Aufgabe 2.2: Verzerrungsleistung]]
+
[[Aufgaben:Exercise_2.2:_Distortion_Power|Exercise 2.2: Distortion Power]]
  
[[Aufgaben:2.2Z_Nochmals_Verzerrungsleistung|Aufgabe 2.2Z: Nochmals Verzerrungsleistung]]
+
[[Aufgaben:Exercise_2.2Z:_Distortion_Power_again|Exercise 2.2Z: Distortion Power again]]
  
 
{{Display}}
 
{{Display}}
  
==Bibliography==
+
==List of sources==
 
<references/>
 
<references/>

Revision as of 22:15, 23 September 2021

# OVERVIEW OF THE SECOND MAIN CHAPTER #


$\text{Definition:}$  In general,  $\text{distortion}$  is understood to be undesirable deterministic changes in a message signal caused by a transmission system.


In addition to stochastic interferences  (noise, crosstalk, etc.), such deterministic distortions are a critical limitation on the transmission quality and rate for many communication systems.

This chapter presents these distortions in a summarising way, in particular:

  • The quantitative detection of such signal falsifications via the distortion power,
  • the distinguishing features between nonlinear and linear distortions,
  • the meaning and computation of the distortion factor in nonlinear systems,  and
  • the effects of linear damping and phase distortions.


Prerequisites for the second main chapter


Description of a linear system

In the following, we consider a system whose input is the signal  $x(t)$  with the corresponding spectrum  $X(f)$.  The output signal is denoted by  $y(t)$  and its spectrum by  $Y(f).$

The block labelled  "system"  can be a part of an electrical circuit or a complete communicarion system consisting of transmitter, channel and receiver.
For the whole main chapter  "Signal Distortions and Equalization"  the following shall apply:

  • The system be time-invariant.  If the input signal  $x(t)$  results in the output signal  $y(t)$, then a later input signal of the same form – in particular  $x(t - t_0)$  – will result in the signal  $y(t - t_0)$.
  • In the following,  no noise  is considered, which is always present in real systems.  For the description of these phenomena we refer to the book  Theory of Stochastic Signals.
  • About the system  no detailed knowledge  is assumed.  In the following, all system properties are derived from the signals  $x(t)$  and  $y(t)$  or their spectra alone.
  • In particular, no specifications are made for the time being with regard to  linearity.  The "system" can be linear (prerequisite for the application of the superposition principle) or non-linear.
  • Not all system properties are discernible from a single test signal  $x(t)$  and its response  $y(t)$ . Therefore,  sufficiently many test signals  must be used for evaluation.


In the following, we will classify communication systems in more detail in this respect.

Ideal and distortion-free system


$\text{Definition:}$  One deals with an  ideal system  if the output signal  $y(t)$  is identical with the input signal  $x(t)$:

$$y(t) \equiv x(t).$$


  • It should be noted that such an ideal system does not exist in reality even if statistical disturbances and noise processes (that always exist but are not considered in this book) are disregarded. 
  • Every transmission medium exhibits losses  (damping)  and transit times.  Even if these physical phenomena are very small, they are never zero.  Therefore it is necessary to introduce a somewhat less strict quality characteristic.


$\text{Definition:}$  A  distortion-free system  exists if the following condition is fulfilled:

$$y(t) = \alpha \cdot x(t - \tau).$$
  • Here,  $α$  describes the damping factor and  $τ$  the transit time.
  • If this condition is not met, the system is said to be  distortive.


$\text{Example 1:}$  The following diagram shows the input signal  $x(t)$  and the output signal  $y(t)$  of a nonideal but distortion-free system.  The system parameters are  $α = 0.8$  and  $τ = 0.25 \ \rm ms$.

Exemplary signals of a distortion-free system

Note:

  • The damping factor  $α$  can be completely reversed by a receiver-side gain of  $1/α = 1.25$, but it must be taken into account that this also increases any noise.
  • However, the transit time  $τ$  cannot be compensated due to  causality reasons.  It now depends on the application whether such a transit time is subjectively perceived as disturbing or not.


  • For example, even with a transit time of one second the  (unidirectional)  TV broadcast of an event is still described as "live". 
  • In contrast to this, transit times of  $\text{300 ms}$  are already perceived as very disturbing in bidirectional communication – e.g. a telephone call.  You either wait for the other person to react or both participants interrupt each other.

Quantitative measure for the signal distortions


Input and output of a distortive system and error signal (below)

We now consider a distortive system on the basis of the input and output signal. 

  • In doing so, we assume that apart from the signal distortions there is no additional damping factor   $α$  which is constant for all frequencies and no additional transit time  $τ$  that is constant for all frequencies.
  • These conditions are fulfilled for the signal sections sketched on the right.
  • In addition to the signals  $x(t)$  and  $y(t)$ , the difference signal is shown in the diagram:
$$\varepsilon(t) = y(t) - x(t).$$

As a quantitative measure of the strength of distortions, for example, the  squared mean of this difference signal is applicable:

$$\overline{\varepsilon^2(t)} = \frac{1}{T_{\rm M}} \cdot \int_{ 0 }^{ T_{\rm M}} {\varepsilon^2(t) }\hspace{0.1cm}{\rm d}t\hspace{0.4cm} \left( = P_{\rm V} \right).$$

The following should be noted about this equation:

  • The measuring time  $T_{\rm M}$  must be chosen sufficiently large.  Actually, this equation should be formulated as a limit process.
  • The squared mean mentioned above is called  "mean squared error"  $\rm (MSE)$  or   distortion power  $P_{\rm V}$  $($because of  "distortion"   ⇒   German:  "Verzerrung"   ⇒   $\rm V)$.
  • If  $x(t)$  and  $y(t)$  are voltage signals, then  $P_{\rm V}$  has the unit of  ${\rm V}^2$, meaning the power is related to the resistance  $R = 1 \ Ω$  according to the above definition.


$\text{Definition:}$  Making use of the power  $P_x$   $($based on  $R = 1 \ Ω)$  of the input signal  $x(t)$  the   $\text{signal–to–distortion (power) ratio}$  can be given as:

$$\rho_{\rm V} = \frac{ P_{x} }{P_{\rm V} } \hspace{0.3cm} \Rightarrow \hspace{0.3cm} 10 \cdot \lg \hspace{0.1cm}\rho_{\rm V} = 10 \cdot \lg \hspace{0.1cm}\frac{ P_{x} }{P_{\rm V} }\hspace{0.3cm} \left( {\rm in \hspace{0.15cm} dB} \right).$$

For the signals shown in the diagram above  $P_x = 4 \ {\rm V}^2$,  $P_{\rm V} = 0.04 \ {\rm V}^2$  and thus  $10 \cdot {\rm lg} \ ρ_{\rm V} = 20 \ \rm dB$ hold.


We reference the interactive applet  Linear Distortions of Periodic Signals.

Elimination of damping factor and transit time


The equations given on the last page do not result in applicable statements if the system is additionanlly affected by an attenuation factor  $α$  and/or a transit time  $τ$.  The diagram shows the attenuated, delayed and distorted signal

Elimination of damping factor $α$ 
and transit time  $τ$
$$y(t) = \alpha \cdot x(t - \tau) + \varepsilon_1(t).$$

The term  $ε_1(t)$  summarises all distortions.  It can be seen from the green area that the error signal  $ε_1(t)$  is relatively small.

In contrast to this, if the attenuation factor  $α$  and the transit time  $τ$  are unknwon, the following should be noted:

  • The error signal  $ε_2(t) = y(t) - x(t)$  determined in this way is relatively large despite small distortions  $ε_1(t)$.
  • Here, instead of the distortion power the distortion energy must be considered because  $x(t)$  and  $y(t)$  are energy-limited signals.
  • The distortion energy is obtained by varying the unknown quantities  $α$  and  $τ$  and thus finding the minimum of the mean squared error:
$$E_{\rm V} = \min_{\alpha, \ \tau} \int_{ - \infty }^{ + \infty} {\big[y(t) - \left(\alpha \cdot x(t - \tau) \right) \big]^2}\hspace{0.1cm}{\rm d}t.$$
  • The energy of the damped and delayed signal  $α · x(t - τ)$  is  $E_{\rm V} =α^2 · E_x$ independent of the transit time  $τ$.  Thus for the signal-to-distortion (power) ratio the following is applicable:
$$\rho_{\rm V} = \frac{ \alpha^2 \cdot E_{x}}{E_{\rm V}}\hspace{0.3cm}{\rm or}\hspace{0.3cm}\rho_{\rm D}= \frac{ \alpha^2 \cdot P_{x}}{P_{\rm V}} .$$
  • The first of these two equations applies to time-limited and thus energy-limited signals, the second one to time-unlimited and thus power-limited signals according to the page  Energy-limited and power-limited signals  in the book "Signal Representation".

Linear and non-linear distortions


A distinction is made between linear and nonlinear distortions:

If the system is linear and time-invariant  $(\rm LTI)$, then it is fully characterised by its  frequency response  $H(f)$ and the following can be stated:

  • According to the  $H(f)$  definition the following holds for the output spectrum:   $Y(f)=X(f) · H(f)$.   As a consequence according to the calculation rules of multiplication,  $Y(f)$  cannot contain any frequency components that are not already contained in  $X(f)$ .
  • The inverse implies:   The output signal  $y(t)$  can include any frequency  $f_0$  already contained in the input  $x(t)$ . The prerequisite is therefore that  $X(f_0) ≠ 0$  holds.
  • For an LTI system the absolute bandwidth  $B_y$  of the output signal is never greater than the bandwidth  $B_x$  of the input signal:   $B_y \le B_x .$


$\text{Conclusion:}$  The differences between linear and non-linear distortions are illustrated by the following diagram:

Linear and nonlinear distortions

In the upper diagram  $B_y = B_x$  holds. There are  linear distortions  because in this frequency band  $X(f)$  and  $Y(f)$  differ.

A band limitation  $(B_y < B_x)$  is a special form of linear distortion, which will be discussed in the  chapter after next.



The lower diagram shows an example of  non-linear distortions  $(B_y > B_x)$.  For such a system no frequency response  $H(f)$  can be given.

Descriptive quantities applicable for non-linear systems will be explained in the next chapter  Non-linear Distortions .
In most real transmission channels both linear and non-linear distortions occur.  However, for a whole range of problems the precise separation of the two types of distortions is essential.  In  [Kam04][1]  a corresponding substitute model is shown.


We refer here to the  (German language)  learning video  Linear and non-Linear distortions.

Exercises for the chapter

Exercise 2.1: Linear? Or Non-Linear?

Exercise 2.1Z: Distortion and Equalisation

Exercise 2.2: Distortion Power

Exercise 2.2Z: Distortion Power again



List of sources

  1. Kammeyer, K.D.:  Nachrichtenübertragung.  Stuttgart: B.G. Teubner, 4. Auflage, 2004.