Statistical Bindings within the Rayleigh Process

Some general remarks on ACF and PSD

The $r(t)$ and $r(t+ \Delta t)$ is suitable for describing the inner statistical dependencies between the neighboring signal values checkLink:_Buch_3 ⇒ Autocorrelation function $\rm (ACF)$:

\[\varphi_r ({\rm \Delta}t) = {1}/{2} \cdot {\rm E}\big [ r(t) \cdot r^{\star}(t + {\rm \Delta}t)\big ] \hspace{0.05cm}.\]

Compared to the definition under the link above, the following differences can be seen:

The ACF–variable is here marked with $\Delta t$ instead of $\tau$ because in this book we need the „$\tau$” still for the 2D–impulse response $h(t, \hspace{0.05cm}\tau)$ .

The equivalent low pass–signal $r(t)$ is complex. By the factor $1/2$ however, the AKF $\varphi_r ({\rm \Delta}t)$ and especially the power $\varphi_r ({\rm \Delta}t = 0)$ refers to the (real) bandpass–Signal $r_{\rm BP}(t)$.

Applying the Rayleighf ading channel model: $r(t) = s(t) \cdot z(t)$. This results for its ACF:

\[\varphi_r ({\rm \Delta}t) = {1}/{2} \cdot {\rm E}\big [ s(t) \cdot z(t) \cdot s^{\star}(t + {\rm \Delta}t) \cdot z^{\star}(t + {\rm \Delta}t)\big ] = \varphi_s ({\rm \Delta}t) \cdot \varphi_z ({\rm \Delta}t)\hspace{0.05cm}.\]

For the ACF of the transmitted signal $s(t)$ and multiplicative factor $z(t)$ the following definitions apply:

\[ \varphi_s ({\rm \Delta}t)= {1}/{2} \cdot {\rm E}\big [ s(t) \cdot s^{\star}(t + {\rm \Delta}t)\big ] \hspace{0.05cm},\]

\[\varphi_z ({\rm \Delta}t) = {\rm E}\big [ z(t) \cdot z^{\star}(t + {\rm \Delta}t)\big ]\hspace{0.05cm}.\]

The factor $1/2$ is only to be considered for the ACF calculation of bandpass signals in the equivalent lowpass range, but not for $\varphi_z ({\rm \Delta}t)$. Otherwise $\varphi_r ({\rm \Delta}t) \ne \varphi_s ({\rm \Delta}t) \cdot \varphi_z ({\rm \Delta}t)$ would result in $\varphi_r ({\rm \Delta}t) $

Based on the definition of $\varphi_z ({\rm \Delta}t) = {\rm E}\big [ z(t) \cdot z^{\star}(t + {\rm \Delta}t)\big ]$ the ACF is always real even with a complex time function $z(t)$ and also with respect to $ {\rm \Delta}t$ even. Let us further consider that

$z(t) = x(t) + {\rm j} \cdot y(t) $ ,

$x(t)$ and $y(t)$ have the same statistical properties, and

that no statistical dependencies exist between $x(t)$ and $y(t)$ ,

so can the ACF of the complex factor $z(t)$ be written as it follows:

\[\varphi_z ({\rm \Delta}t) = \varphi_x ({\rm \Delta}t) + \varphi_y ({\rm \Delta}t) = 2 \cdot \varphi_x ({\rm \Delta}t) \hspace{0.05cm}.\]

$\text{Conclusion:}$ This results in the following simplification:

To determine the statistical dependencies of the complex variable $z(t)$ only one of the two Gaussian processes must be considered. In the following, this is $x(t)$.

We first calculate the autocorrelation function $\rm (ACF)$ $\varphi_x ({\rm \Delta}t) = {\rm E}\big[x(t) \cdot x(t + {\rm \Delta}t)\big]$ of the real part and then its power density spectrum $\rm (PSD)$

\[{\it \Phi}_x (f_{\rm D}) = \int_{-\infty}^{+\infty} \varphi_x ({\rm \Delta}t) \cdot {\rm e}^{ -- {\rm j \cdot 2 \pi} \cdot f_{\rm D} \cdot {\rm \Delta}t } \hspace{0.15cm}{\rm d}( {\rm \Delta}t) \hspace{0.3cm} \bullet\!\!-\!\!\!-\!\!\!-\!\!\circ \hspace{0.3cm} \varphi_x ({\rm \Delta}t) \hspace{0.05cm}. \]

For the corresponding parameters of the complex random process $z(t)$ we have:

\[\varphi_z ({\rm \Delta}t) = 2 \cdot \varphi_x ({\rm \Delta}t)\hspace{0.05cm},\hspace{0.2cm} {\it \Phi}_z (f_{\rm D}) = 2 \cdot {\it \Phi}_x (f_{\rm D}) \hspace{0.05cm}.\]

The $\rm PSD$–Variable is the Doppler frequency $f_{\rm D}$, because in mobile radio the so-called "Doppler effect" is the cause of the statistical dependencies.

This effect is explained on the next page.

Phenomenological description of the Doppler effect

The statistical dependencies within the real "signals" $x(t)$ and $y(t)$ or within the complex quantity $z(t)$ are due to the Doppler effect. This was predicted theoretically in the middle of the 19th century by the Austrian mathematician, physicist and astronomer Christian Andreas Doppler and named after him.

$\text{Definition:}$ The Doppler effect refers to the change in the perceived frequency of waves of any kind that occurs when the source (transmitter) and observer (receiver) move relative to each other.

Qualitatively, the Doppler effect can be described as follows:

If the observer and source approach each other, the frequency increases from the observer's point of view, regardless of whether the observer is moving or the source or both.

If the source moves away from the observer or the observer moves away from the source, the observer perceives a lower frequency than that actually transmitted.

$\text{Example 1:}$ We look at the pitch change of the "Martinhorn" of an ambulance. As long as the vehicle approaches, the observer hears a higher tone than when the car is stationary. When the ambulance moves away, a lower tone is perceived.

The same effect can be seen with a car racing note. The frequency changes and the sound are the more obvious the faster the cars are going.

In this learning tutorial you can illustrate the subject matter with the interactive applet The Doppler Effect .

Initial situation: $\rm (S)$ and $\rm (E)$ are not moving

$\text{Example 2:}$ Some properties of this effect, which is still known from physics lessons, will now be shown by means of snapshots of an earlier version of the above mentioned animation, where the dynamic program properties are of course lost.

The first diagram shows the initial situation:

The stationary station $\rm (S)$ outputs the constant frequency $f_{\rm S}$ .
The wave propagation is illustrated in the diagram by concentric circles around $\rm (S)$ .
If the receiver $\rm (E)$ is also at rest, the frequency $f_{\rm E} = f_{\rm S}$ is then perceived

Doppler effect: $\rm (S)$ moves towards resting $\rm (E)$

$\text{Example 3:}$ The next snapshot shows the case where the transmitter $\rm (S)$ has moved at constant speed $v$ from its starting point $\rm (S_0)$ towards the receiver $\rm (E)$

The right diagram shows that the frequency $f_{\rm E}$ (blue oscillation) perceived by the receiver is larger by about $20\%$ than the frequency $f_{\rm S}$ at the transmitter (red oscillation).
Due to the movement of the transmitter, the circles are no longer concentric.

Doppler effect: $\rm (S)$ moves away from resting $\rm (E)$

The scenario shown on the left results when the transmitter $\rm (S)$ moves away from the receiver $\rm (E)$ Then the received frequency $f_{\rm E}$ (blue oscillation) is about $20\%$ smaller than the transmitted frequency $f_{\rm S}$.

$\text{However, the following must be taken into account:}$

All these figures apply to unrealistically high speed $(v = c/5)$, where $c = 3 \cdot 10^8 \, {\rm m/s}$ indicates the speed of light. In mobile radio, the deviations between $f_{\rm S}$ and $f_{\rm E}$ are usually only a fraction of the transmission frequency.
The exact equation for the receiving frequency $f_{\rm E}$ ,including an angle $\alpha$ between the direction of movement and the connecting line transmitter–receiver, is

\[f_{\rm E} = f_{\rm S} \cdot \frac{\sqrt{1 - (v/c)^2} }{1 - v/c \cdot \cos(\alpha)} \hspace{0.05cm}.\]

As the Exercise 1.4Z will show, at realistic speeds $(v \ll c)$ one can assume the following approximation, in which the effects described by the Theory of Relativity are disregarded

\[f_{\rm E} \approx f_{\rm S} \cdot \big [1 +{v}/{c} \cdot \cos(\alpha) \big ] \hspace{0.05cm}.\]

Doppler frequency and its distribution

We summarize the statements of the last page again briefly, whereby we start from the second, i.e. the non–relativistic equation:

A relative movement between transmitter (source) and receiver (observer) results in a shift by the Doppler frequency $f_{\rm D} = f_{\rm E} - f_{\rm S}$.

A positive Doppler frequency $(f_{\rm E} > f_{\rm S})$ results when transmitter and receiver (relative) move towards each other. A negative Doppler frequency $(f_{\rm E} < f_{\rm S})$ means that transmitter and receiver (directly or at an angle) move away from each other.

The maximum frequency shift occurs when transmitter and receiver move directly towards each other ⇒ angle $\alpha = 0^\circ$. This maximum value depends first approximation on the transmission frequency $ f_{\rm S}$ and the speed $v$ depends $(c = 3 \cdot 10^8 \, {\rm m/s}$ indicates the speed of light$)$:

\[f_{\rm D, \hspace{0.05cm} max} = f_{\rm S} \cdot {v}/{c} \hspace{0.05cm}.\]

If the relative movement takes place at any angle $\alpha$ to the connecting line transmitter–receiver, a Doppler shift of

\[f_{\rm D} = f_{\rm E} - f_{\rm S} = f_{\rm D, \hspace{0.05cm} max} \cdot \cos(\alpha) \hspace{0.3cm} \Rightarrow \hspace{0.3cm} - \hspace{-0.05cm}f_{\rm D, \hspace{0.05cm} max} \le f_{\rm D} \le + \hspace{-0.05cm}f_{\rm D, \hspace{0.05cm} max} \hspace{0.05cm}.\]

$\text{Conclusion:}$ Assuming equal probable directions of motion $($Equal distribution for the angle $\alpha$ in the range $- \pi \le \alpha \le +\pi)$ the probability density function $($here denoted with "wdf" (from the german WahrscheinlichkeitsDichteFunktion)$)$ the Doppler frequency in the range $- f_\text{D, max} \le f_{\rm D} \le + f_\text{D, max}$:

\[{\rm wdf}(f_{\rm D}) = \frac{1}{2\pi \cdot f_{\rm D, \hspace{0.05cm} max} \cdot \sqrt {1 - (f_{\rm D}/f_{\rm D, \hspace{0.05cm} max})^2 } } \hspace{0.05cm}.\]

Outside the range between $-f_{\rm D}$ and $+f_{\rm D}$ the probability density function always has the value zero.

$\text{Derivation:}$ The resulting Doppler frequency depending on the angle of movement $\alpha$ is

To calculate the probability density function $\rm (PDF)$ of the Doppler frequency

\[f_{\rm D} = f_{\rm D, \hspace{0.05cm} max} \cdot \cos(\alpha) = g(\alpha) \hspace{0.05cm}.\]

We refer to this function as $g(\alpha)$ and assume that

$\alpha$ takes all angle values between $\pm \pi$
with equal probability ⇒ equal distribution.&nbsp

Then for the probability of the Doppler frequency according to the chapter Transformation of Random Variables in the book "Stochastic Signal Theory":

\[{\rm wdf}(f_{\rm D})=\frac{ {\rm wdf}(\alpha)}{\vert g\hspace{0.08cm}'(\alpha)\vert}\Bigg \vert_{\hspace{0.1cm} \alpha=h(f_{\rm D})} \hspace{0.05cm}\]

the derivative $g\hspace{0.08cm}'(\alpha)= - f_\text{D, max} \cdot \sin(\alpha)$, and
the inverse function $ \alpha = h(f_{\rm D})$.

In the example the inverse function is

$$ \alpha = \arccos(f_{\rm D}/f_{\rm D, \hspace{0.05cm} max}).$$

The diagram illustrates the calculation procedure for determining the Doppler frequency's PDF:

Since the characteristic curve between the Doppler frequency $f_{\rm D}$ and the angle $\alpha$ ⇒ $ g(\alpha) = f_{\rm D, \hspace{0.05cm} max} \cdot \cos(\alpha)$ is limited by the value $f_{\rm D, \hspace{0.05cm} max}$ is for $f_{\rm D}$ no value outside this range possible.

When transforming random variables, a distinction must be made between areas with positive and negative slopes of the transformation's characteristic curve. The $\alpha$–values between $-\pi$ and $0$ $($positive gradient of the transformation characteristic$)$ between the Doppler frequency $f_{\rm D}$ and the angle $\alpha$ provide the result

\[{\rm wdf}(f_{\rm D})=\frac{1/(2\pi)}{f_{\rm D, \hspace{0.05cm} max} \cdot \sin(\alpha)} \Bigg \vert_{\hspace{0.1cm} \alpha=\arccos(f_{\rm D}/f_{\rm D, \hspace{0.05cm} max})} = \frac{(2\pi \cdot f_{\rm D, \hspace{0.05cm} max} )^{-1} }{ \sin(\arccos(f_{\rm D}/f_{\rm D, \hspace{0.05cm} max}))} = \frac{1}{2\pi \cdot f_{\rm D, \hspace{0.05cm} max} \cdot \sqrt { 1 - (f_{\rm D}/f_{\rm D, \hspace{0.05cm} max})^2 } } \hspace{0.05cm}.\]

For reasons of symmetry, the positive $\alpha$–area contributes in the same way, so that the inner total area is:

\[{\rm wdf}(f_{\rm D}) = \frac{1}{\pi \cdot f_{\rm D, \hspace{0.05cm} max} \cdot \sqrt { 1 - (f_{\rm D}/f_{\rm D, \hspace{0.05cm} max})^2 } } \hspace{0.05cm}.\]

If $\alpha$ takes values around $\pm \pi/2$ it results in a small Doppler frequency ⇒ $f_{\rm D} \approx 0$ $($violet marking$)$. But, because of the relatively large gradient of the cosine curve $g(\alpha)$ at $\alpha = \pm \pi/2$ the PDF–value at $f_{\rm D} \approx 0$ ist very small.

Small angles $($um $\alpha \approx 0)$ however, lead to the maximum Doppler frequency ⇒ $f_{\rm D} \approx f_{\rm D, \hspace{0.05cm} max}$ $($red marker$)$. Because of the nearly horizontal characteristic curve $g(\alpha)$ the $f_{\rm D}$–PDF is clearly larger here. For $f_{\rm D} \equiv f_{\rm D, \hspace{0.05cm} max}$ this even results in an infinitely large value.

On the other hand, if $\alpha$ takes values around $\pm \pi$ it leads to the Doppler frequency $f_{\rm D} \approx -f_{\rm D, \hspace{0.05cm} max}$ $($green marker$)$. Again the characteristic curve is nearly horizontal and again it results in a large PDF–value.

ACF und PSD with Rayleigh–Fading

We now assume an antenna with the same radiation in all directions; the Doppler–PSD is then identical in shape to the PDF of the Doppler frequencies.

For ${\it \Phi}_x(f_{\rm D})$ the PDF must still be multiplied by the power $\sigma^2$ of the Gaussian process, and the resulting PSD ${\it \Phi}_z(f_{\rm D})$ of the complex factor $z(t) = x(t) + {\rm j} \cdot y(t) $ can be written after doubling as:

\[{\it \Phi}_z(f_{\rm D}) = \left\{ \begin{array}{c} (2\sigma^2)/( \pi \cdot f_{\rm D, \hspace{0.05cm} max}) \cdot \left [ 1 - (f_{\rm D}/f_{\rm D, \hspace{0.05cm} max})^2 \right ]^{-0.5} \\ 0 \end{array} \right.\quad \begin{array}{*{1}c} {\rm f\ddot{u}r}\hspace{0.15cm} |f_{\rm D}| \le f_{\rm D, \hspace{0.05cm} max} \\ {\rm sonst} \\ \end{array} \hspace{0.05cm}.\]

This process is named after William C. Jakes Jr. the Jakes–Spectrum. The doubling is necessary, because up to now only the contribution of the real part $x(t)$ was considered.

The corresponding autocorrelation function (ACF) is obtained after a Fourier inverse transformation:

\[\varphi_z ({\rm \Delta}t) = 2 \sigma^2 \cdot {\rm J_0}(2\pi \cdot f_{\rm D, \hspace{0.05cm} max} \cdot {\rm \Delta}t)\hspace{0.05cm},\]

with the Bessel function of first kind and zero order (first equation: definition, second equation: series expansion):

\[{\rm J }_0 (u) = \frac{1}{ 2\pi} \cdot \int_{0}^{2\pi} {\rm e }^{- {\rm j }\hspace{0.03cm}\cdot \hspace{0.03cm}u \hspace{0.03cm}\cdot \hspace{0.03cm}\cos(\alpha)} \,{\rm d} \alpha \hspace{0.2cm} = \hspace{0.2cm} \sum_{k = 0}^{\infty} \frac{(-1)^k \cdot (u/2)^{2k}}{k! \cdot \Gamma (k+1)} \hspace{0.05cm}.\]

The numerical values of this function can be obtained with the applet of the same name.

Doppler-PSD and time function (magnitude in dB) for Rayleigh fading with Doppler effect

$\text{Example 4:}$ Shown on the left is the Jakes–spectrum

for $f_{\rm D, \hspace{0.05cm} max} = 50 \ \ \rm Hz$ (blue curve) as well as
for $f_{\rm D, \hspace{0.05cm} max} = 100 \ \rm Hz$ (red curve).

For GSM–D–Netz $(f_{\rm S} = 900 \ \rm MHz)$ these values correspond to the speeds $v = 60 \ \rm km/h$ bzw. $v = 120 \ \rm km/h$.

For E–Netz $(f_{\rm S} = 1.8 \ \rm GHz)$ these values apply to half as high speeds: $v = 30 \ \ \rm km/h$ or. $v = 60 \ \rm km/h$.

The right picture shows the logarithmic absolute value of $z(t)$:

You can see the twice as fast fading of the red curve
The Rayleigh–PDF (amplitude distribution) is independent of $f_{\rm D, \hspace{0.05cm} max}$ and therefore the same for both cases.

The right picture shows the logarithmic absolute value of $z(t)$:

You can see that the red curve fades twice as fast.
The Rayleigh–PDF (amplitude distribution) is independent of $f_{\rm D, \hspace{0.05cm} max}$ and therefore the same for both cases.}}

Exercises to the chapter

Exercise 1.4: Rayleigh PDF and Jakes PSD

Exercise 1.4Z: On the Doppler Effect

Exercise 1.5: Reconstruction of the Jakes Spectrum