Further Developments of ISDN

From LNTwww


Broadband ISDN


Broadband ISDN – usually abbreviated as  $\text{B–ISDN}$  – was a advancement of ISDN.  The aim of this further development from 1996 was to enable new communications services with higher bandwidths in addition to the services and applications of narrowband ISDN.  B-ISDN supports,  for example,  audiovisual services and multimedia applications such as video transmission,  videophone and videoconferencing with transmission rates of up to a maximum of  $155$  Mbps.

To achieve such a large transmission rate,  B-ISDN uses the following new technologies:

  • Instead of copper cables,  optical fibers are used,  which enable greater bandwidths and ranges due to their low attenuation.  The advantages of  fiber optic technology  are summarized in the next section.
  • ATM technology  $($Asynchronous Transfer Mode$)$  is used to transmit and switch the information.  The last section explains this technology for broadband ISDN.
  • The local and long-distance exchanges are specially designed for these large bandwidths.
Narrowband ISDN  (below) and broadband ISDN  (above)  in comparison Korrektur


The graphic shows

  • below an ISDN network with two bearer channels  ("narrowband ISDN")  via a copper twisted pair  ("Co–TP"),
  • compared with broadband ISDN via fiber optic cable  $\rm (FOC)$ at the top.
  • Signaling takes place via another copper twisted pair  (in the center).


Broadband ISDN failed to achieve great commercial success because this technology was very expensive and sufficient bandwidths could also be achieved with  $\rm DSL$  ("Digital Subscriber Line").

  • The high costs are related to the fact that the optical fiber must be laid all the way to the subscriber.
  • However,  larger  (and therefore less flexible)  companies and public authorities use B-ISDN for a longer time,  with data rates of up to  $622$  Mbit/s being achieved after further modifications.


Fiber optic technology


The transmission media used for broadband ISDN were  fiber optic cables  $\rm (FOC)$,Broadband ISDN often also referred to in simplified terms as  "optical fibers".  Since the first attempts in the 1970s,  optical transmission technology has made enormous progress and offers many advantages over electrical transmission:

  1.   In a fiber optic cable, signal propagation occurs through a guided electromagnetic field and there are no currents or voltages as in copper cables.  A fiber optic cable is therefore "insensitive to electromagnetic noise"  and is also much lighter than a copper cable.

  2.  The signal attenuation of an optical fiber is significantly lower than that of a copper cable. At the "attenuation minimum" at the wavelength  $λ = 1.55 \ µ{\rm m}$,  a value of  $\text{0.2 dB/km}$  is reached. For comparison:   For a copper cable with a diameter of 0.4 mm, the attenuation value for a DC signal is about  $\text{5 dB/km}$  and for a megahertz about  $\text{20 dB/km}$  – see section  "Attenuation behavior of copper cables".
  • Today (2018), optical fibers can achieve transmission rates of  $\text{100 Gbit/s}$  and – with intermediate optical amplifiers – distances of several  $\text{1000 km}$  and more. Intermediate regenerators are now only used in exchanges, as the routing of data is still largely electronic.
  • Current optical transmission systems transport data rates of  $\text{100 Gbit/s}$  over a distance of several  $\text{1000 km}$ at a single wavelength. There are already (2018) systems commercially available at  $\text{400 Gbit/s}$,  but using multiple wavelengths.
  •   Optical Wavelength Division Multiplex  (WDM)  allows a large number of channels to be transmitted in parallel. In 2017, a total data rate of  $\text{70.4 terabits/s}$  was thus achieved via a transatlantic submarine cable  $\rm (1 \ terabit = 10^{12} \ bits)$.
  • Nowadays, fiber is mainly used between exchanges, while existing copper lines continue to be used between subscribers and exchanges for cost reasons. In the longer term, however, there will certainly be  Fiber–to–the–Home  (FttH).


E/O and O/E signal conversion


In the exchanges, electrical-to-optical conversion (E/O) must be performed at the transmitting end by a laser diode  (LD) or an LED (Light–emitting Diode).

At the receiver, an optical-electrical reconversion (O/E) by a photodiode (PD) is then necessary.

Note:   "APD" stands for avalanche photodiode.





UG2 interface


In a fiber optic connection, the reference point between the network termination and the local exchange is referred to as  $\rm U_{G2}$. This interface consists of two optical fibers for the two transmission directions.

Conversion from HDB3 to 1T2B code
  • Since it is not possible to transmit the ternary HDB3 code with the value set  $\{–1, \ 0, +1\}$  of the  $\rm S_{2M}$ interface in optical form without a complex optical modulator, this must be converted back into a binary code with the elements  $0$  and  $1$  for the  $\rm U_{G2}$ interface.


  • This conversion is done redundantly with the  1T2B code. This means:  Each ternary symbol is represented by two binary symbols according to the given table. The code redundancy here is equal to  $1 – \log_2 \hspace{0.05cm} (3)/2 ≈ 20.7\%$.


This results in the following properties:

  • The conversion doubles the step rate to  $\text{4096 kbit/s}$,  which is in principle a disadvantage, but is more than compensated by the advantages of optical transmission.
  • A real disadvantage is the additional effort required by the receiver to convert the optical signal into an electrical signal.


ATM technology


Broadband ISDN is based on the so-called  ATM technology  ('Asynchronous Transfer Mode). Compared with PCM 30, ATM offers the following advantages for broadband services and applications:

ATM cell structure
  • flexible access to the data,
  • good adaptation to high bit rates.


Here follows only a brief description of the  "ATM method"  and how it works:

  • ATM is a special connection-oriented packet switching, and the packets here are called ATM cells.
  • It is therefore a packet-oriented transmission of cells.


Each ATM cell is composed of 53 bytes and consists of the cell header (5 bytes) and an information field (48 bytes), which is used for the transmission of user information or signaling data.

The cell header contains:

  • the Generic Flow Control (GFC) – 4 bits to control the cell flow,
  • the Virtual Path Identifier (VPI) – 8 bits for virtual path identification,
  • the Virtual Channel Identifier (VCI) – 16 bits for virtual channel identification,
  • the Payload Type (PT) – 3 bits to describe the cell type,
  • the Cell Loss Priority (CLP) – one bit to detect a cell loss,
  • the Header Error Control (HEC) – 8 bits to avoid bit errors in the cell header.


In ATM technology, cells arriving asynchronously from the terminals are transmitted using time division multiplexing. If no cells arrive, empty cells are generated so that there is always a continuous stream of cells on the line. ATM is asynchronous in the sense that cells with user information do not have to occur periodically.

Further information on ATM can be found in the second main chapter  "DSL" (Digital Subscriber Line), which also uses ATM technology.


Exercise for the chapter


Exercise 1.7: Coding for B-ISDN