Difference between revisions of "Aufgaben:Exercise 2.9: Symmetrical Distortions"

From LNTwww
 
(31 intermediate revisions by 5 users not shown)
Line 1: Line 1:
{{quiz-Header|Buchseite=Modulationsverfahren/Hüllkurvendemodulation
+
{{quiz-Header|Buchseite=Modulation_Methods/Envelope_Demodulation
 
}}
 
}}
  
[[File:P_ID1040__Mod_Z_2_8.png|right|]]
+
[[File:P_ID1040__Mod_Z_2_8.png|right|frame|Transmitter and receiver spectrum in the equivalent low-pass region]]
Das aus zwei Anteilen zusammengesetzte Quellensignal
+
The source signal made up of two components
$$q(t) = A_1 \cdot \cos(2 \pi f_1 t ) + A_2 \cdot \cos(2 \pi f_2 t )$$
+
:$$q(t) = A_1 \cdot \cos(2 \pi f_1 t ) + A_2 \cdot \cos(2 \pi f_2 t )$$
wird amplitudenmoduliert und über einen linear verzerrenden Übertragungskanal übertragen. Die Trägerfrequenz ist $f_T$ und der zugesetzte Gleichanteil $A_T$. Es liegt also eine ZSB–AM mit Träger vor.
+
is amplitude modulated and transmitted through a linearly distorting transmission channel. 
 +
*The carrier frequency is   $f_{\rm T}$  and the added DC component  $A_{\rm T}$. 
 +
*Thus,  a  "double-sideband amplitude moduluation"  $\rm (DSB–AM)$ with carrier"  is present.
  
Die obere Grafik zeigt das Spektrum $S_{TP}(f)$ des äquivalenten TP–Signals in schematischer Form. Das bedeutet, dass die Längen der gezeichneten Diraclinien nicht den tatsächlichen Werten von $A_T$, $A_1/2$ und $A_2/2$ entsprechen.
 
  
 +
The upper graph shows the spectrum  $S_{\rm TP}(f)$  of the equivalent low-pass signal in schematic form.  This means that the lengths of the Dirac delta lines drawn do not correspond to the actual values of   $A_{\rm T}$,  $A_1/2$  and  $A_2/2$.
  
Messtechnisch erfasst wurde die Spektralfunktion $R(f)$ des Empfangssignals. In der unteren Grafik sehen Sie das daraus berechnete äquivalente Tiefpass–Spektrum $R_{TP}(f)$.
 
  
Der Kanalfrequenzgang ist durch einige Stützwerte ausreichend genau beschrieben:
+
The spectral function  $R(f)$  of the received signal was measured.  In the lower graph we can observe the equivalent low-pass spectrum  $R_{\rm TP}(f)$ calculated from this.
$$ H_{\rm K}(f = f_{\rm T}) = 0.5,\hspace{0.3cm}H_{\rm K}(f = f_{\rm T} \pm f_1) = 0.4,\hspace{0.3cm} H_{\rm K}(f = f_{\rm T} \pm f_2) = 0.2 \hspace{0.05cm}.$$
 
'''Hinweis:''' Diese Aufgabe bezieht sich auf den Theorieteil von [http://en.lntwww.de/Modulationsverfahren/H%C3%BCllkurvendemodulation Kapitel 2.3].  
 
  
===Fragebogen===
+
The channel frequency response is characterized with sufficient accuracy with a few auxiliary values:
 +
:$$ H_{\rm K}(f = f_{\rm T}) = 0.5,$$
 +
:$$H_{\rm K}(f = f_{\rm T} \pm f_1) = 0.4,$$
 +
:$$ H_{\rm K}(f = f_{\rm T} \pm f_2) = 0.2 \hspace{0.05cm}.$$
 +
 
 +
 
 +
 
 +
 
 +
Hints:
 +
*This exercise belongs to the chapter  [[Modulation_Methods/Envelope_Demodulation|Envelope Demodulation]].
 +
*Particular reference is made to the section  [[Modulation_Methods/Envelope_Demodulation#Description_using_the_equivalent_low-pass_signal|Description using the equivalent low-pass signal]].
 +
 +
 
 +
 
 +
===Questions===
  
 
<quiz display=simple>
 
<quiz display=simple>
{Multiple-Choice Frage
 
|type="[]"}
 
- Falsch
 
+ Richtig
 
  
 +
{Give the amplitudes of the carrier and source signal.
 +
|type="{}"}
 +
$A_{\rm T} \ = \hspace{0.17cm} $  { 4 3% } $\ \rm V$
 +
$A_1 \ = \ $ { 3 3% } $\ \rm V$
 +
$A_2 \ = \ $ { 4 3% } $\ \rm V$
  
{Input-Box Frage
+
{Which kind of distortion would the application of an envelope demodulator in an ideal channel &nbsp; &rArr; &nbsp; $H_{\rm K}(f) = 1$&nbsp; lead to?
|type="{}"}
+
|type="()"}
$\alpha$ = { 0.3 }
+
- No distortion.
 +
- Linear distortions.
 +
+ Nonlinear distortions.
  
 +
{Calculate the equivalent low-pass signal and answer the following questions. Is it true that...
 +
|type="[]"}
 +
+ $r_{\rm TP}(t)$&nbsp; is always real,
 +
+ $r_{\rm TP}(t)$&nbsp; is always greater than or equal to zero,
 +
- the phase function &nbsp;$ϕ(t)$&nbsp; can take on the values &nbsp;$0^\circ$&nbsp; and &nbsp;$180^\circ$&nbsp;.
  
 +
{Which kind of distortion does the envelope demodulator in the observed transmission channel lead to?
 +
|type="()"}
 +
- No distortion.
 +
+ Linear distortions.
 +
- Nonlinear distortions.<br>
  
 
</quiz>
 
</quiz>
  
===Musterlösung===
+
===Solution===
 
{{ML-Kopf}}
 
{{ML-Kopf}}
'''1.'''
+
'''(1)'''&nbsp; On the basis of the graphs on the exercise page,&nbsp; the following statements can be made:
'''2.'''
+
:$${A_{\rm T}} \cdot 0.5 = 2 \,{\rm V}\hspace{0.3cm}  \Rightarrow  \hspace{0.3cm}A_{\rm T} \hspace{0.15cm}\underline {= 4 \,{\rm V}},$$
'''3.'''
+
:$${A_{\rm 1}}/{2} \cdot 0.4 = 0.6\,{\rm V}\hspace{0.3cm}  \Rightarrow  \hspace{0.3cm}A_{\rm 1} \hspace{0.15cm}\underline {= 3 \,{\rm V}},$$
'''4.'''
+
:$${A_{\rm 2}}/{2} \cdot 0.2 = 0.4\,{\rm V}\hspace{0.3cm}  \Rightarrow  \hspace{0.3cm}A_{\rm 2} \hspace{0.15cm}\underline {= 4 \,{\rm V}}\hspace{0.05cm}.$$
'''5.'''
+
 
'''6.'''
+
 
'''7.'''
+
 
 +
'''(2)'''&nbsp; <u>Answer 3</u>&nbsp; is correct:
 +
*The resulting modulation depth is &nbsp; $m = (A_1 + A_2)/A_T = 1.75 >1$.
 +
*This leads to strong nonlinear distortion when using an envelope demodulator.
 +
*A distortion factor cannot be specified because the source signal contains two frequency components.
 +
 
 +
 
 +
 
 +
 
 +
'''(3)'''&nbsp; <u>Answers 1 and 2</u> are correct:
 +
*The Fourier retransform of &nbsp; $R_{\rm TP}(f)$&nbsp; gives us the result:
 +
:$$ r_{\rm TP}(t) = 2 \,{\rm V} + 1.2 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 0.8 \,{\rm V} \cdot \cos(2 \pi f_2 t )\hspace{0.05cm}.$$
 +
*This function is always real and non-negative.
 +
*Thus,&nbsp; $ϕ(t) = 0$&nbsp; holds simultaneously,&nbsp; whereas&nbsp; $ϕ(t) = 180^\circ$&nbsp; is not possible.
 +
 
 +
 
 +
 
 +
 
 +
'''(4)'''&nbsp; A comparison of the two signals
 +
:$$q(t)  =  3 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 4 \,{\rm V} \cdot \cos(2 \pi f_2 t ),$$
 +
:$$ v(t)  =  0.4 \cdot 3 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 0.2 \cdot 4 \,{\rm V} \cdot \cos(2 \pi f_2 t )$$
 +
:shows,&nbsp; that linear (attenuation) distortions now arise  &nbsp; &rArr; &nbsp;  <u>Answer 2</u>.
 +
 
 +
*Here, the channel&nbsp; $H_{\rm K}(f)$&nbsp; has the positive effect,&nbsp; that instead of irreversible nonlinear distortions,&nbsp; only linear distortions arise,&nbsp; and these can be eliminated by a downstream filter.
 +
*This is due to the fact that the higher attenuation of the source signal&nbsp; $q(t)$&nbsp; compared to the carrier signal&nbsp; $z(t)$&nbsp; lowers the modulation depth from &nbsp; $m = 1.75$&nbsp; to&nbsp;
 +
:$$m = (0.4 · 3 \ \rm  V + 0.2 · 4 \ \rm  V)/(0.5 · 4 \ \rm  V) = 1.$$
 +
 
 +
 
 +
 
 
{{ML-Fuß}}
 
{{ML-Fuß}}
  
  
[[Category:Aufgaben zu Modulationsverfahren|^2.3 Hüllkurvendemodulation^]]
+
[[Category:Modulation Methods: Exercises|^2.3 Envelope Demodulation^]]

Latest revision as of 15:20, 18 January 2023

Transmitter and receiver spectrum in the equivalent low-pass region

The source signal made up of two components

$$q(t) = A_1 \cdot \cos(2 \pi f_1 t ) + A_2 \cdot \cos(2 \pi f_2 t )$$

is amplitude modulated and transmitted through a linearly distorting transmission channel. 

  • The carrier frequency is  $f_{\rm T}$  and the added DC component  $A_{\rm T}$. 
  • Thus,  a  "double-sideband amplitude moduluation"  $\rm (DSB–AM)$ with carrier"  is present.


The upper graph shows the spectrum  $S_{\rm TP}(f)$  of the equivalent low-pass signal in schematic form.  This means that the lengths of the Dirac delta lines drawn do not correspond to the actual values of  $A_{\rm T}$,  $A_1/2$  and  $A_2/2$.


The spectral function  $R(f)$  of the received signal was measured.  In the lower graph we can observe the equivalent low-pass spectrum  $R_{\rm TP}(f)$ calculated from this.

The channel frequency response is characterized with sufficient accuracy with a few auxiliary values:

$$ H_{\rm K}(f = f_{\rm T}) = 0.5,$$
$$H_{\rm K}(f = f_{\rm T} \pm f_1) = 0.4,$$
$$ H_{\rm K}(f = f_{\rm T} \pm f_2) = 0.2 \hspace{0.05cm}.$$



Hints:


Questions

1

Give the amplitudes of the carrier and source signal.

$A_{\rm T} \ = \hspace{0.17cm} $

$\ \rm V$
$A_1 \ = \ $

$\ \rm V$
$A_2 \ = \ $

$\ \rm V$

2

Which kind of distortion would the application of an envelope demodulator in an ideal channel   ⇒   $H_{\rm K}(f) = 1$  lead to?

No distortion.
Linear distortions.
Nonlinear distortions.

3

Calculate the equivalent low-pass signal and answer the following questions. Is it true that...

$r_{\rm TP}(t)$  is always real,
$r_{\rm TP}(t)$  is always greater than or equal to zero,
the phase function  $ϕ(t)$  can take on the values  $0^\circ$  and  $180^\circ$ .

4

Which kind of distortion does the envelope demodulator in the observed transmission channel lead to?

No distortion.
Linear distortions.
Nonlinear distortions.


Solution

(1)  On the basis of the graphs on the exercise page,  the following statements can be made:

$${A_{\rm T}} \cdot 0.5 = 2 \,{\rm V}\hspace{0.3cm} \Rightarrow \hspace{0.3cm}A_{\rm T} \hspace{0.15cm}\underline {= 4 \,{\rm V}},$$
$${A_{\rm 1}}/{2} \cdot 0.4 = 0.6\,{\rm V}\hspace{0.3cm} \Rightarrow \hspace{0.3cm}A_{\rm 1} \hspace{0.15cm}\underline {= 3 \,{\rm V}},$$
$${A_{\rm 2}}/{2} \cdot 0.2 = 0.4\,{\rm V}\hspace{0.3cm} \Rightarrow \hspace{0.3cm}A_{\rm 2} \hspace{0.15cm}\underline {= 4 \,{\rm V}}\hspace{0.05cm}.$$


(2)  Answer 3  is correct:

  • The resulting modulation depth is   $m = (A_1 + A_2)/A_T = 1.75 >1$.
  • This leads to strong nonlinear distortion when using an envelope demodulator.
  • A distortion factor cannot be specified because the source signal contains two frequency components.



(3)  Answers 1 and 2 are correct:

  • The Fourier retransform of   $R_{\rm TP}(f)$  gives us the result:
$$ r_{\rm TP}(t) = 2 \,{\rm V} + 1.2 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 0.8 \,{\rm V} \cdot \cos(2 \pi f_2 t )\hspace{0.05cm}.$$
  • This function is always real and non-negative.
  • Thus,  $ϕ(t) = 0$  holds simultaneously,  whereas  $ϕ(t) = 180^\circ$  is not possible.



(4)  A comparison of the two signals

$$q(t) = 3 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 4 \,{\rm V} \cdot \cos(2 \pi f_2 t ),$$
$$ v(t) = 0.4 \cdot 3 \,{\rm V} \cdot \cos(2 \pi f_1 t ) + 0.2 \cdot 4 \,{\rm V} \cdot \cos(2 \pi f_2 t )$$
shows,  that linear (attenuation) distortions now arise   ⇒   Answer 2.
  • Here, the channel  $H_{\rm K}(f)$  has the positive effect,  that instead of irreversible nonlinear distortions,  only linear distortions arise,  and these can be eliminated by a downstream filter.
  • This is due to the fact that the higher attenuation of the source signal  $q(t)$  compared to the carrier signal  $z(t)$  lowers the modulation depth from   $m = 1.75$  to 
$$m = (0.4 · 3 \ \rm V + 0.2 · 4 \ \rm V)/(0.5 · 4 \ \rm V) = 1.$$