Further Developments of the GSM

1. Examples of Communication Systems
2. GSM – Global System for Mobile Communications
3. Further Developments of the GSM

• Previous page
• Next page

• Previous page
• Next page

The different generations of the GSM

GSM was originally designed and developed as a pan-European mobile communications network, primarily for telephone calls and fax. Data transmission at a constant low data rate was secondary. The GSM standard was further developed in various phases after its presentation. This enabled new services.

The different generations of the GSM

The graph from  [EVB01]  shows the further developments of GSM:

• The  $\rm GSM$ system described so far in the third main chapter is limited to the first two generations. The  $\rm phase \ 1$  included only basic teleservices and a few additional services that could be offered on a mandatory basis by all network operators at that time when GSM was launched in 1991.
• The standardization of the $\rm phase \ 2$  in the years from 1995 to 1997 already included the first further developments of the GSM standard. As a result, the additional services known from  "ISDN"  were also gradually made available for GSM and supplemented by some new features, such as call waiting  or hold  (Hold).
• In the years 1997-2000, new data services with higher data rates were developed, such as.

"High Speed Circuit-Switched Data"  (HSCSD),

"General Packet Radio Service"  (GPRS), and

"Enhanced Data Rates for GSM Evolution"  (EDGE).

These newer data services are classified as part of the $\rm phase \ 2+$  (or Generation 2.5) and are highlighted in green in the graphic.

• The third generation of mobile communications includes  "UMTS"  (Universal Mobile Telecommunications System). This standard enabled significantly higher data transmission rates than were possible with the GSM standard. It is discussed in detail in the fourth main chapter of this book. In the graphic above, this third-generation system is highlighted in red.

The innovations of the  $\rm phase \ 2+$  affect almost all aspects of GSM, from radio transmission to call control. The new data services made possible by this are explained in more detail on the following pages.

High Speed Circuit–Switched Data (HSCSD)

"Bundling of multiple timeslots in HSCSD"

The GSM data transmission standard  $\rm High \ Speed \ Circuit-Switched \ Data$  (HSCSD), introduced in 1999, allowed the user data rate per connection to be increased from  $9.6 \rm kbit/s$  to  $14.4 \rm kbit/s$  when transmission conditions permitted.

By bundling several adjacent time slots, the data rate could be increased even further.

The data rate depends on how many channels the network operator provides for bundling or how many channels the HSCSD cell phone can process.

The graphic explains the principle of bundling multiple timeslots:

• Each of the eight physical channels (timeslots) in a frame provides a maximum  $14.4 \rm kbit/s$  for data communication. HSCSD enables channel bundling by combining multiple timeslots, as is also used in ISDN. This is referred to as  multislot capability.
• By interconnecting all eight channels, this would result in  $\rm 8 - 14.4 \ kbit/s = 115.2 \ kbit/s$. However, since the connection between the  Base Station Controller  (BSC) and the  Mobile Switching Center  (MSC) is limited to  $64 \rm kbit/s$ , one is limited to bundling four time slots, resulting in a maximum transmission rate of  $57.6 \rm kbit/s$ .
• An advantage of HSCSD technology over packet-oriented GPRS (see next page) is the line-oriented data transmission. This is particularly advantageous for applications that require uniform bandwidths, since here the transmission channel does not have to be shared with anyone. Examples include video and image transmission.
• However, the higher transmission costs due to the occupancy of multiple channels are disadvantageous. These channels are therefore no longer available to other mobile subscribers. In a radio cell with high channel utilization, it can therefore happen that the bundling of multiple channels is prevented by the network operator.

General Packet Radio Service (GPRS)

With the GSM extension  $\rm General \ Packet \ Radio \ Service$  (GPRS), packet-oriented data transmission was made possible for the first time in 2000. GPRS supports a large number of protocols (Internet Protocol, X.25, Datex-P, etc.) and allows mobile subscribers to communicate with external data networks (the Internet or internal company intranets). GPRS was an important intermediate step in the evolution of cellular mobile networks towards third generation and towards the mobile Internet.

A GPRS user benefits from shorter access times and the higher data rate $($to  $21.4 \ \rm kbit/s)$  compared to conventional GSM  $(9.6 \ \rm kbit/s)$  and HSCSD  $(14.4 \ \rm kbit/s)$. With GPRS, the charges are not based on the connection duration, but on the actual amount of data transferred. Therefore, a radio channel does not have to be permanently reserved for a user (as is the case with HSCSD).

GPRS system architecture

To introduce GPRS, some modifications and additions to the GSM network were necessary, as shown in the graphic "GPRS System Architecture" from  [BVE99]  summarized are:

• Blue lines describe payload and signaling data.
• The orange dotted connections denote signaling data.
• Gb, Gc, Gd, etc. indicate interfaces of GPRS.

To integrate GPRS into the existing GSM system architecture, a new class of network nodes is added to it.

The additional GPRS components - highlighted by red circles in the diagram - are explained here only in bullet points:

• The  GPRS Support Nodes  (GSN) are responsible for the transmission and traffic routing  (routing)  of data packets between the mobile stations and the external packet-switched data networks. Here, a distinction is made between SGSN and GGSN, which communicate with each other via an IP-based GPRS backbone network.
• The  Serving GPRS Support Node  (SGSN) is responsible for mobility management and performs a similar function for packet data services as the  Mobile Switching Center  (MSC) does for connection-oriented voice signals.
• The  Gateway GPRS Support Node  (GGSN) is the interface to foreign packet-oriented data networks. It converts the GPRS packets coming from the SGSN into the appropriate protocol  (IP, X.25, ...)  and sends them out to the  Packet Data Network  (PDN).

GPRS air interface

When a GPRS cell phone is switched on, it first performs the "Cell Selection" procedure by searching for a frequency channel with GPRS data. If such a channel has been found, then depending on the cell phone class, the cell phone must be manually set to GPRS services or it can automatically and dynamically switch between GPRS and GSM. A distinction is made between:

• Class  $\rm A$  devices can handle GPRS data services and GSM transmission services simultaneously; channel resources are monitored in parallel in a packet-switched and circuit-switched manner.
• In class  $\rm B$  the signaling channels of GSM and GPRS are monitored simultaneously as long as no service is switched through. However, parallel GSM/GPRS operation is not possible.
• In class  $\rm C$  the subscriber must decide beforehand whether to use the mobile for GSM or GPRS, since signaling channels can no longer be monitored simultaneously.

To be able to switch the GSM radio interface to packet-oriented GPRS operation, the logical channels had to be extended. Logical GPRS channels can be recognized by a preceding "P", which indicates the packet-oriented operating mode. Almost for all logical GSM channels there is the corresponding GPRS equivalent:

• The  Packet Data Traffic Channel  (PDTCH) is used in GPRS as  traffic channel  for user data transfer. The corresponding GSM channel is called TCH.
• The  signaling channels  are divided into the  Packet Broadcast Control Channel  (PBCCH), the  Packet Common Control Channel  (PCCCH), and the  Packet Dedicated Control Channel  (PDCCH), as in GSM.

GPRS allows subscribers to exchange data with public data networks and, like GSM, uses GMSK modulation and the FDMA/TDMA combination with eight time slots per TDMA frame. The differences are as follows:

• In the GSM standard, each active mobile station is assigned exactly one time slot of a TDMA frame. This physical channel is reserved for the mobile station for the entire duration of a call, both in the uplink and in the downlink.
• In GPRS, up to eight time slots can be combined for rate enhancement. In addition, uplink and downlink are allocated separately. The physical channels are reserved only for the duration of the transmission of data packets and then released again.

GPRS channel coding

In contrast to conventional GSM $($with the data rate  $9.6 \ \rm kbit/s)$  four possible  coding schemes  are defined for GPRS, which can be used depending on the reception quality:

• Coding scheme 1 $(\rm CS-1)$  with  $9.05 \rm kbit/s$  (181 bits per 20 ms),
• Coding scheme 2 $(\rm CS-2)$  with  $13.4 \rm kbit/s$  (268 bits per 20 ms),
• Coding scheme 3 $(\rm CS-3)$  with  $15.6 \rm kbit/s$  (312 bits per 20 ms),
• Coding scheme 4 $(\rm CS-4)$  with  $21.4 \rm kbit/s$  (428 bits per 20 ms).

The smallest possible data rate is thus  $9.05 \rm kbit/s$  ($\rm CS-1$, one time slot), the maximum is currently (2007)  $171.2 \rm kbit/s$  ($\rm CS-4$, eight time slots). However, this theoretical speed is not achieved in practice, since most current GPRS phones only support a maximum net data rate of  $13.4 \rm kbit/s$  ($\rm CS-2$). The graphic and the following explanations refer to this combination.

For channel coding in GPRS

• The  $268$  information bits are first supplemented by six precoded bits of the  Uplink State Flag  (USF),  $16$  parity bit of the so-called  Block Check Sequence  (BCS) and four tail bits  $(0000)$ . The latter are necessary for the termination of the convolutional codes.
• For channel coding, the convolutional code of code rate  $R_{\rm C} = 1/2$  known from GSM is used. By this the total  $294$ bits  are doubled to  $588$  bits and thus sufficiently protected against transmission errors.
• Followed by  $132$  of these  $588$  bits are punctured, so that finally a codeword of length  $456$  bit $($bitrate  $22.8 \ \rm kbit/s)$  results. This gives a resulting code rate (from convolutional encoders including puncturing) of  $294/456 ≈ 65\%$.
• After channel coding, the codewords are fed to a block interleaver of depth  $4$ . The interleaving scheme is identical for all four coding schemes.

Enhanced Data Rates for GSM Evolution

Die letzte GSM–Erweiterung  $\rm Enhanced \ Data \ Rates \ for \ GSM–Evolution$  (EDGE) mit dem Ziel, die Datenübertragungsrate in GSM–Netzen zu erhöhen, benutzt neben  Gaussian Minimum Shift Keying  (GMSK) als zusätzliches Modulationsverfahren  8–Phase Shift Keying  (8–PSK):

• Bei diesem gibt es acht verschiedene Symbole (bei GMSK nur zwei), die sich durch unterschiedliche Phasenlagen bei Vielfachen von  $45^\circ$  unterscheiden.
• Das bedeutet, dass mit jedem Symbol drei Datenbit übertragen werden können, wodurch die Datenrate im Vergleich zu GPRS um den Faktor  $3$  gesteigert wird.

Mit der Definition von EDGE wird HSCSD zu  Enhanced Circuit Switched Data  (E–CSD) und GPRS zu  Enhanced–GPRS  (E–GPRS). T–mobile ist allerdings der einzige deutsche Netzbetreiber, der derzeit (2007) EDGE in seinem Netz anbietet.

Normal Burst  von EDGE bzw. E–GPRS

Die Grafik zeigt den  Normal Burst  von EDGE bzw. E–GPRS. Man erkennt folgende Unterschiede zum  Normal Burst  bei GSM:

• Der  Normal Burst  besteht bei EDGE aus  $468.75$  Bit anstelle der  $156.25$  Bit bei GSM, woraus die Verdreifachung der Datenrate ersichtlich ist.
• Wie bei GSM gibt es zwei  Stealing Flags. Tailbits, Trainingssequenz und  Guard Period  werden jeweils verdreifacht. Damit verbleiben für das Datenfeld  $57 · 3 + 2 = 173$ Bit.
• Somit werden bei E–GPRS im  Normal Burst  $346$  Bit kanalcodierte Daten  $($Coderate  $R_{\rm C} =1/2)$  pro  $576.9\ \rm µ s$  übertragen, was einer Netto–Datenrate von ca.  $60 \ \rm kbit/s$  entspricht.

Modulation and Coding Schemes bei E–GPRS

Bei E–GPRS gibt es neun vom Betreiber auswählbare  Modulation and Coding Schemes  (MCS), die von den verwendeten Kanalcodier– und Modulationsverfahren abhängen.

Tabelle der  Modulation and Coding Schemes  bei E–GPRS

Die Tabelle zeigt die möglichen Schemata von E–GPRS. Daraus ist zu erkennen:

• Die ersten vier Schemata verwenden wie GSM/GPRS das Modulationsverfahren GMSK mit einem bit Information pro Kanalzugriff, während bei  $\rm MCS–5$, ... ,  $\rm MCS–9$  eine achtstufige Phasenmodulation (8–PSK) benutzt wird und damit drei bit pro Symbol übertragen werden.
• Je kleiner die Coderate, desto größer ist die zugesetzte Redundanz und damit die Datensicherheit. Insbesondere zwischen  $\rm MCS–4$  $(R_{\rm C} = 1)$  und  $\rm MCS–5$  $(R_{\rm C} = 0.37)$  nimmt die Coderate wegen der günstigeren Modulationsart trotz höherer Netto–Datenrate signifikant ab (letzte Spalte).
• Der aufwändigste Modus  $\rm MCS–9$  bietet gemäß der Tabelle eine Datenrate von  $59.2 \ \rm kbit/s$  und erlaubt theoretisch die gleichzeitige Belegung von acht Zeitschlitzen, was eine maximale Netto–Datenrate von  $473.6 \ \rm kbit/s$  bedeuten würde. Allerdings ist dieser Modus  $($mit $R_{\rm C} = 1)$  nur bei extrem guten Bedingungen anwendbar und acht Zeitschlitze stehen auch nur selten zur Verfügung.
• Mit  $\rm MCS–8$  und sieben Zeitschlitzen kann man immerhin schon  $380.8 \ \rm kbit/s$  erreichen und ist damit in der Größenordnung von  Universal Mobile Telecommunications System  (UMTS), dem bekanntesten Standard der dritten Mobilfunkgeneration, der derzeit  $384 \ \rm kbit/s$  anbietet.
• EDGE verwendet die gleichen Frequenzen wie GSM, weshalb diese Technik besonders für Betreiber mit bestehender GSM–Infrastruktur interessant ist, die im Jahr 2000 keine der teueren UMTS–Lizenzen erworben haben und trotzdem eine ausreichend hohe Datenrate anbieten wollen.

Das System UMTS wird im nachfolgenden vierten Hauptkapitel eingehend beschrieben.

Aufgabe zum Kapitel

Aufgabe 3.8: General Packet Radio Service