Difference between revisions of "Aufgaben:Exercise 1.1: Music Signals"
From LNTwww
| Line 61: | Line 61: | ||
===Solution=== | ===Solution=== | ||
{{ML-Kopf}} | {{ML-Kopf}} | ||
| − | '''(1)''' Correct is | + | '''(1)''' Correct is <u>solution 2</u>: |
*In the marked range of $20$ milliseconds approx. $10$ oscillations can be detected. | *In the marked range of $20$ milliseconds approx. $10$ oscillations can be detected. | ||
*From this the result follows approximately for the signal frequency: $f = {10}/(20 \,\text{ms}) = 500 \,\text{Hz}$. | *From this the result follows approximately for the signal frequency: $f = {10}/(20 \,\text{ms}) = 500 \,\text{Hz}$. | ||
| Line 67: | Line 67: | ||
| − | '''(2)''' Correct is | + | '''(2)''' Correct is <u>solution 1</u>: |
*The signal <math>v_1(t)</math> is undistorted compared to the original signal <math>q(t)</math>. The following applies: $v_1(t)=\alpha \cdot q(t-\tau)$. | *The signal <math>v_1(t)</math> is undistorted compared to the original signal <math>q(t)</math>. The following applies: $v_1(t)=\alpha \cdot q(t-\tau)$. | ||
| Line 75: | Line 75: | ||
'''(3)''' Correct are the <u>solutions 1 and 3</u>: | '''(3)''' Correct are the <u>solutions 1 and 3</u>: | ||
| − | *One can recognize additive noise both in the displayed signal <math>v_2(t)</math> and in the audio signal ⇒ <u>solution 3</u>. | + | *One can recognize additive noise both in the displayed signal <math>v_2(t)</math> and in the audio signal ⇒ <u>solution 3</u>. |
| − | *The signal-to-noise ratio is approx. $\text{30 dB}$ $($but this cannot be seen from | + | |
| + | *The signal-to-noise ratio is approx. $\text{30 dB}$ $($but this cannot be seen from the mentioned data$)$. | ||
| + | |||
*Correct is also <u>solution 1</u>: Without this noise component <math>v_2(t)</math> would be identical with <math>q(t)</math>. | *Correct is also <u>solution 1</u>: Without this noise component <math>v_2(t)</math> would be identical with <math>q(t)</math>. | ||
Revision as of 16:20, 12 January 2024
Music signals,
original, noisy and/or distorted?
original, noisy and/or distorted?
On the right you see a $\text{30 ms}$ long section of a music signal \(q(t)\). It is the piece »For Elise« by Ludwig van Beethoven.
- Underneath are drawn two sink signals \(v_1(t)\) and \(v_2(t)\), which were recorded after the transmission of the music signal \(q(t)\) over two different channels.
- The following operating elements allow you to listen to the first fourteen seconds of each of the three audio signals \(q(t)\), \(v_1(t)\) and \(v_2(t)\).
Original signal \(q(t)\):
Sink signal \(v_1(t)\):
Sink signal \(v_2(t)\):
Notes:
- The exercise belongs to the chapter »Principles of Communication«.
Questions
Solution
(1) Correct is solution 2:
- In the marked range of $20$ milliseconds approx. $10$ oscillations can be detected.
- From this the result follows approximately for the signal frequency: $f = {10}/(20 \,\text{ms}) = 500 \,\text{Hz}$.
(2) Correct is solution 1:
- The signal \(v_1(t)\) is undistorted compared to the original signal \(q(t)\). The following applies: $v_1(t)=\alpha \cdot q(t-\tau)$.
- An attenuation \(\alpha\) and a delay time \(\tau\) do not cause distortion, but the signal is then only quieter and delayed in time, compared to the original.
(3) Correct are the solutions 1 and 3:
- One can recognize additive noise both in the displayed signal \(v_2(t)\) and in the audio signal ⇒ solution 3.
- The signal-to-noise ratio is approx. $\text{30 dB}$ $($but this cannot be seen from the mentioned data$)$.
- Correct is also solution 1: Without this noise component \(v_2(t)\) would be identical with \(q(t)\).
(4) The signal \(v_1(t)\) is identical in form to the original signal \(q(t)\) and differs from it only
- by the attenuation factor $\alpha = \underline{\text{0.3}}$ $($this corresponds to about $\text{–10 dB)}$
- and the delay time $\tau = \underline{10\,\text{ms}}$.
