Mobile Communications/Physical Layer for LTE

1. Mobile Communications
2. LTE – Long Term Evolution
3. Physical Layer for LTE

• Previous page
• Next page

• Previous page
• Next page

General Description

The   Physical Layer is the lowest layer in the OSI–layer model of the  International Organization for Standardization  (ISO), which is also called  Bit transmission layer . It describes the physical transmission of bit sequences in LTE and the operation of the various channels according to the 3GPP–specification. All specifications are valid for  Frequency Division Duplex  (FDD) as well as for  Time Division Duplex  (TDD).

Protocol Architecture for LTE

The diagram shows the layers of the LTE–protocol architecture. The communication between the individual layers takes place via three different types of channels:

• Logical channels,
  
• Transport channels,
  
• physical channels.
  
  

This chapter deals with the communication between sender and receiver in the lowest, red highlighted  physical layer.

Basically it should be noted:

• Exactly like the Internet, LTE uses exclusively packet-based transmission, i.e. without specifically assigning resources to a single user.
  

• The design of the LTE–physical layer is therefore characterized by the principle of dynamically allocated network resources.
  

• The physical layer plays a key role in the efficient allocation and utilization of available system resources.

According to this graphic the physical layer communicates with

• the block  Medium Access Control  (MAC) and exchanges information about the users and the regulation or control of the network via so-called transport channels,
  

• the block  Radio Resource Control  (RRC), where control commands and measurements are continuously exchanged to adapt the transmission to the channel quality.
  
  

The complexity of the LTE–transmission is to be indicated by the following diagram, which has been directly adopted by the  European Telecommunications Standards Institute  (ETSI). It shows the communication between the individual layers (channels) and applies exclusively to the downlink.

Communication between the individual layers in the LTE downlink

• On the following pages we will take a closer look at the physical layer and the physical channels. We distinguish between uplink and downlink, but we will limit ourselves to the essentials.

• In reality, the individual channels take over a number of other functions, but their description would go beyond the scope of this tutorial.

• If you are interested, you can find a detailed description in  [HT09].

Physical channels in uplink

LTE uses the multiple access method SC–FDMA in the uplink transmission from the terminal device to the base station. Accordingly, the following physical channels exist in the 3GPP–specification:

• Physical Uplink Shared Channel  (PUSCH),
  
• Physical Random Access Channel  (PRACH),
  
• Physical Uplink Control Channel  (PUCCH).
  
  

The user data are transmitted in the physical channel  PUSH . The transmission speed depends on how much bandwidth is available to the user at that moment. The transmission is based on dynamically allocated resources in time and frequency range with a resolution of one millisecond or 180 kHz.This allocation is performed by the  Scheduler  in the base station (eNodeB ). A terminal device cannot transmit any data without instructions from the base station.

The exception is the use of the physical channel  'PRACH, the only channel in the LTE–uplink with non–synchronized transmission. The function of this channel is the request for permission to send data via one of the other two physical channels. By sending a  Cyclic Prefix  and a signature on the PRACH, the terminal and base station are synchronized and are thus ready for further transmissions.

The third uplink–channel  PUCCH  is used exclusively for the transmission of control signals. By this one understands

• positive and negative acknowledgements of receipt (ACK/NACK),
  

• Requests for repeated transmission (in case of NACK), and
  

• the exchange of channel quality information between the terminal and the base station.
  
  

If, in addition to the control data, user data is sent from the terminal to the base station at the same time, such control signals can also be transmitted via the PUSCH. If no user data is to be transmitted, PUCCH is used instead.

A simultaneous use of PUSCH and PUCCH is not possible due to restrictions of the SC–transmission method SC–FDMA. If only one  Shared Channel  had been selected for all control information, one would have had to choose between

• intermittent problems with user data transmission, or
  

• permanently too few resources for the control information.
  
  

The information about the channel quality is obtained by means of so-called reference symbols. As indicators for the channel quality this information is then sent

• to  Channel Quality Indicator  (CQI), and
  

• to  Rank Indicator  (RI).
  
  

A detailed explanation of the quality guarantee can be found, for example, in  [HR09]  and  [HT09].

$\text{Example 1:}$  The reference symbols or channel quality information are distributed in the PUSCH according to the following graphic.

distribution of reference symbols and user data in PUSCH

This describes the arrangement of the useful information and the signaling data in a "virtual" subcarrier.

• Virtual because SC–FDMA does not have subcarriers like OFDMA.

• The reference symbols are necessary to estimate the channel quality.
  

• This information is also transferred as  Channel Quality Indicator  (CQI)  or as  Rank Indicator  (RI)  via the PUSCH.

Physical channels in downlink

In contrast to the uplink, LTE uses the multiple access method  OFDMA in the downlink, i.e. during transmission from the base station to the terminal. Accordingly, the 3GPP–Consortium specified the following physical channels for this purpose:

• Physical Downlink Shared Channel  (PDSCH),
  

• Physical Downlink Control Channel  (PDCCH),
  

• Physical Control Format Indicator Channel  (PCFICH),
  

• Physical Hybrid ARQ Indicator Channel  (PHICH),
  

• Physical Broadcast Channel  (PBCH),
  

• Physical Multicast Channel  (PMCH).
  
  

The user data are transmitted via the  PDSCH . The resource allocation is done both in the time domain (with a resolution of one millisecond) and in the frequency domain (resolution:  180 kHz). Due to the use of OFDMA as transmission method, the individual speed of each user depends on the number of assigned resource blocks (à 180 kHz). A eNodeB allocates the resources related to the channel quality of each individual user.

The  PDCCH  contains all information regarding the allocation of resource blocks or bandwidth for both the uplink and the downlink. A terminal device thereby receives information about how many resources are available.

Division between PDCCH and PDSCH in LTE downlink

The diagram shows an example of the division between the channels PDCCH and PDSCH:

• The PDCCH can occupy up to four symbols per subframe (in the graphic: two).
  
• This leaves twelve time slots for the user data (i.e. for the channel PDSCH).

Via channel  PCFICH  the terminal device is informed how many symbols are to be assigned to the control information of the PDCCH. The purpose of this dynamic division between control– and user data is as follows:

• On the one hand, many users can be supported in this way, each with a low data rate. This scenario requires more tuning, which means that in this case the PDCCH would have to contain three or four symbols.
  

• On the other hand, the overhead caused by PDCCH can be reduced by assigning a high data rate to only a few concurrent users.

Distribution of reference symbols in the downlink

In addition to the PDCCH, reference symbols are also required in the downlink to estimate the channel quality and calculate the  Channel Quality Indicator  (CQI) . These reference symbols are distributed over the subcarriers (different frequencies) or symbols (different times) as shown in the adjacent figure.
Regarding the other physical channels of the LTE–Downlink is to be noted:

• The only purpose of the downlink–channel  PHICH  (Physical Hybrid ARQ Indicator Channel ) is to signal whether a packet sent in the uplink has arrived.
  

• On the broadcast–channel  PBCH  (Physical Broadcast Channel ) the base stations send system information with operating parameters as well as synchronization signals, which are required for registration in the network, to all mobile terminals in the radio cell approximately every 40 milliseconds.
  

• The Multicast–channel  PMCH  (Physical Multicast Channel ) has a similar purpose, information for so-called Multicast–transmissions – is sent to several receivers simultaneously through this channel. This could be, for example, mobile television via LTE, which is planned for a future release, or something similar.
  

Processes on the physical layer

By "processes in the physical layer" one understands different methods and procedures, which are used in the bit transmission layer. Among them fall among other things:

• Timing Advance,
  

• Paging,
  

• Random Access,
  

• Channel Feedback Reporting,
  

• Power Control,
  

• Hybrid Adaptive Repeat and Request.
  
  

A complete list with the corresponding description can be found in  [HT09]. Only the last two procedures will be discussed in more detail here.

Power control with LTE

By  Power Control  one understands generally the control of the transmission power with the goal,

• to improve the transmission quality,
  

• to increase the network capacity, and
  

• reduce the power consumption.
  
  

With regard to the last point, the standardization of LTE had to take this into account:

• On the one hand, the power consumption in the end devices was to be minimized in order to guarantee longer battery runtimes for them.
  

• On the other hand, it should be avoided that the base stations have to provide too much power.
  
  

With LTE,  Power Control  is only applied in the uplink, whereas it is more of an "slow" power control. This means that the procedure specified in LTE does not have to react as quickly as for example in UMTS (W–CDMA ). The reason is that by using the orthogonal carrier system "SC–FMDA" the so-called  Near–Far–Problem does not exist.

• To be precise, for LTE the Power Control  does not control the absolute power, but the spectral power density, i.e. the power per bandwidth.
  

• Instead of trying to smooth power peaks by temporarily reducing the transmission power, power peaks can also be used to increase the data rate for a short time.
  
  

All in all, LTE–power control is intended to find the optimum balance between the lowest possible power and at the same time interference that is still acceptable for the transmission quality (QoS). This is specifically achieved by estimating the loss during transmission and by calculating a correction factor according to the current site characteristics. The statements made here are largely taken from  [DFJ08].

Hybrid Adaptive Repeat and Request

Every communication system needs a scheme for retransmission of lost data due to transmission errors to ensure sufficient transmission quality. In LTE  Hybrid Adaptive Repeat and Request  (HARQ)  was specified for this purpose. This procedure is also used in  UMTS  in a similar form.

The procedure based on the  stop–and–wait–technique is as follows:

• After a terminal device has received a packet from the base station, it is decoded and feedback is sent via the  PUCCH.
  

• In case of a failed transmission ("NACK") the packet is resent. Only if the transmission was successful (Feedback:  "ACK"), the next packet is sent.
  
  

In order to ensure continuous data transfer despite the stop–and–wait–procedure, LTE requires several simultaneous HARQ–processes. In LTE, eight parallel processes are used both in the uplink and in the downlink.

$\text{Example 2:}$  The graphic illustrates how it works with eight simultaneous HARQ–processes:

HARQ in LTE with eight simultaneous processes

• In this example, the first process fails in the first attempt to transfer packet 1.
• The receiver tells this "Fail" to the sender by a "NACK".
• In contrast, the second parallel process is successful with its first packet:   "Pass".
  
• In the next step (i.e. after the other seven HARQ–processes have sent) the first HARQ retransmits its last sent packet due to the acknowledgement "NACK"
  

• The second process sends a new packet due to the acknowledgement "ACK" now.
  
  

The other processes, which were ignored in this example, proceed in the same way.

Modulation for LTE

LTE uses the modulation method  Quadrature–Amplitude Modulation. Different variants are available in the uplink as well as in the downlink, namely

• 4–QAM (identical to QPSK)  ⇒  2 bits per symbol,
  

• 16–QAM  ⇒  4 bits per symbol,
  

• 64–QAM  ⇒  6 bits per symbol.
  

The signal space constellations of these variants are shown in the following graphic.
.

Note:   QAM is not an LTE–specific development, but is also used in many already established wired transmission methods, such as those of DSL (Digital Subscriber Line).

possible QAM signal space constellations in LTE

Depending on the environmental conditions and distance to the base station, the  Scheduler  selects the appropriate QAM–method (see figure):

Modulation method, depending on distance from base station

• 64–QAM allows the best data rates, but is also the most susceptible to transmission interference and is therefore only used near the base stations.
  

• The weaker the connection, the simpler the modulation method must be, which also reduces the spectral efficiency (in bit/s per Hertz).
  
• Very robust is 4–QAM with only two bits per symbol (one each for real– and imaginary part). This can be used for much larger distances than 16–QAM.
  , for example

• Due to the exact same signal space constellation the 4–QAM is often called  Quaternary Phase Shift Keying  (QPSK). The four signal space points are arranged in a square pattern (QAM–principle). But they also lie on a circle (characteristic of the PSK).
  .

throughput depending on SNR

The left graphic from [MG08] gives the following facts:

• With 4–QAM or QPSK (two bit/symbol) a throughput (throughput ) of almost one Mbit/s is achieved in the LTE–uplink with the assumptions made in  [MG08]  [MG08] .

• Only above a certain signal strength (english:   Signal–to–Noise Ratio, SNR) a higher level QAM is used, for example 16–QAM (4 bit/symbol) or 64–QAM (8 bit/symbol).
  

• If the SNR is sufficiently large, increasing the number of stages will lead to better results regarding the data throughput.

It should be noted that the low-rate QPSK (4–QAM) is always used in the control channels, since this information

• on the one hand, do not require high data rates due to their small size, and
  

• on the other hand should be received (almost) error-free due to their importance.
  
  

An exception is the channel  PUSCH  in the uplink, which transmits both user– and control data. For this reason, the same modulation type is used here for both signals.

Scheduling for LTE

All LTE–base stations contain a scheduler that can be switched between

• a total transfer rate as high as possible
  

• with sufficiently good Quality of Service (QoS)
  
  

A QoS–criterion is for example the  packet delay duration. So the scheduler tries to optimize the overall situation by using algorithms.

Scheduling is necessary to ensure a fair distribution of resources. A concrete example is that a user who currently has a poor channel and therefore low efficiency must still be allocated sufficient resources, otherwise the desired (and guaranteed) transmission quality cannot be maintained.

The scheduler controls the selection of the modulation method and the subcarrier–mapping. The functionality of the scheduler is illustrated by the following graphic for the uplink. Similar statements apply to the downlink.

Functionality of the scheduler in the LTE uplink

$\text{Conclusion:}$  Based on [SABM06], [WGM07] and [MG08] should be noted in summary:

• Scheduler algorithms are often very complicated due to the many optimization criteria, parameters and possible scenarios. Therefore, the design is usually based on an optimal system in which each base station knows the channel transmission functions sufficiently well at all times and transmission delays are unproblematic.
  

• From these boundary conditions, different approaches are created with the help of mathematical analyses  [WGM07], whose effectiveness can only be verified by practical tests. A detailed description of such tests can be found in  [MG08].
  

• In principle, the overall transmission rate can be increased by channel-dependent scheduling (exploiting frequency selectivity), but this involves a large overhead, since test signals must be sent over the entire bandwidth. The information has to be distributed to all end devices if the full optimization potential is to be exploited.
  

• In various tests, the clear and significant advantages (doubling of throughput) of channel-based scheduling were shown, but also the expected losses with faster moving users. More about this in the recommended document  [SABM06].

Due to many advantages, scheduling is an integral part of the LTE–Release 8, specified by 3GPP.

Exercises to chapter

Exercise 4.4: Modulation in LTE

[[Aufgaben:Exercise 4.4Z: Physical Channels in LTE]