Digital Signal Transmission/Linear Nyquist Equalization

1. Digital Signal Transmission
2. Intersymbol Interfering and Equalization Methods
3. Linear Nyquist Equalization

• Previous page
• Next page

• Previous page
• Next page

Structure of the optimal Nyquist equalizer

Block diagram of the optimal Nyquist equalizer

In this section we assume the following block diagram of a binary system. In this regard, it should be noted:

• The Dirac source provides the message to be transmitted in binary bipolar form   ⇒   amplitude coefficients  $a_\nu \in \{ -1, \hspace{0.05cm}+1\}$. The source is assumed to be redundancy-free.
  

• The transmission pulse shape  $g_s(t)$  is taken into account by the transmitter frequency response  $H_{\rm S}(f)$.  In all examples,  $H_{\rm S}(f) = {\rm si}(\pi f T)$  is based   ⇒   NRZ rectangular transmission pulses.
  

In some derivations, transmitter and channel are combined by the common frequency response  $H_{\rm SK}(f) = H_{\rm S}(f) \cdot H_{\rm K}(f)$. 

• The receiver filter  $H_{\rm E}(f)$  is multiplicatively composed of the  matched filter  $H_{\rm MF}(f) = H_{\rm SK}^\star(f)$  and the  transversal filter  $H_{\rm TF}(f)$, at least it can be split up mentally in this way.

• The total frequency response between the Dirac source and the threshold decision should satisfy the   first Nyquist condition.  Thus, it must hold:

$$H_{\rm S}(f) \cdot H_{\rm K}(f) \cdot H_{\rm MF}(f) \cdot H_{\rm TF}(f) = H_{\rm Nyq}(f) \hspace{0.05cm}.$$

• With this condition, there is no intersymbol interference and the maximum eye opening is obtained. Therefore, the  detection SNR  and  system efficiency  for binary signaling are:

$$\rho_d = \frac{2 \cdot s_0^2 \cdot T}{\sigma_d^2} = \frac{2 \cdot s_0^2 \cdot T}{N_0}\cdot \frac{1}{\sigma_{d,\hspace{0.05cm} {\rm norm}}^2} \hspace{0.3cm}\Rightarrow \hspace{0.3cm} \eta = \frac{\rho_d }{\rho_{d,\hspace{0.05cm} {\rm max}}} = \frac{\rho_d }{2 \cdot s_0^2 \cdot T/N_0} = \frac{1}{\sigma_{d,\hspace{0.05cm} {\rm norm}}^2} \hspace{0.05cm}.$$

• The optimization task is therefore limited to determining the receiver filter  $H_{\rm E}(f)$  such that the normalized noise power before the decision takes the smallest possible value:

\[\sigma_{d,\hspace{0.05cm} {\rm norm}}^2 = \frac{\sigma_d^2}{N_0/ T} =T \cdot \int_{-\infty}^{+\infty} |H_{\rm E}(f)|^2 \,{\rm d} f \stackrel {!}{=} {\rm minimum}\hspace{0.05cm}.\]

$\text{Definition:}$  We refer to the configuration described here as  Optimal Nyquist Equalization (ONE). Although this can also – and especially effectively – be applied to multi-level systems, we initially set  $M = 2$.

Mode of action of the transversal filter

Transversal filter (second order) as part of the optimal Nyquist equalizer

Let us first clarify the task of the symmetric transversal filter

$$H_{\rm TF}(f) \hspace{0.4cm}\bullet\!\!-\!\!\!-\!\!\!-\!\!\circ \hspace{0.4cm} h_{\rm TF}(t) = \sum_{\lambda = -N}^{+N} k_\lambda \cdot \delta(t - \lambda \cdot T) $$

with the following properties:

• $N$  indicates the order of the filter   ⇒   the graph shows a second order filter  $(N=2)$.
• For the filter coefficients  $k_{-\lambda} = k_{\lambda}$   ⇒   symmetric structure   ⇒   $H_{\rm TF}(f)$ is real.
• $H_{\rm TF}(f)$  is thus completely determined by the coefficients  $k_0$, ... , $k_N$  completely determined.

For the input pulse  $g_m(t)$  we assume without restriction of generality that it is

• symmetric about  $t=0$  (output of the matched filter),
  
• has the value  $g_m(\nu)$ at times  $\nu \cdot T$  and  $-\nu \cdot T$,  respectively.
  

Thus, the input pulse values are:

$$\text{...}\hspace{0.2cm} , g_m(3),\hspace{0.15cm}g_m(2),\hspace{0.15cm}g_m(1),\hspace{0.15cm}\hspace {0.15cm}g_m(0),\hspace{0.15cm}g_m(1),\hspace{0.15cm}g_m(2),\hspace{0.15cm}g_m(3),\hspace{0.1cm} \text{...}\hspace{0.05cm}.$$

Consequently, for the basic transmitter pulse  $g_d(t)$  at the filter output, the following values result at the time instants  $\nu \cdot T$  with the abbreviations  $g_0 =g_d(t= 0)$,   $g_1 =g_d(t= \pm T)$,   $g_2 =g_d(t= \pm 2T)$: 

$$ t = 0\hspace{-0.1cm}:\hspace{0.9cm}g_0 = k_0 \cdot g_m(0) + k_1 \cdot 2 \cdot g_m(1) \hspace{1.23cm}+k_2 \cdot 2 \cdot g_m(2),\hspace{0.05cm} $$

$$ t = \pm T\hspace{-0.1cm}:\hspace{0.45cm}g_1 = k_0 \cdot g_m(1) + k_1 \cdot \big [g_m(0)+g_m(2)]+ k_2 \cdot [g_m(1)+g_m(3) \big ], $$

$$ t = \pm 2T\hspace{-0.1cm}:\hspace{0.2cm}g_2 = k_0 \cdot g_m(2) + k_1 \cdot \big [g_m(1)+g_m(3)\big ]+ k_2 \cdot \big [g_m(2)+g_m(4)\big ] \hspace{0.05cm}. $$

From this system with three linearly independent equations, one can now determine the filter coefficients  $k_0$,  $k_1$  and  $k_2$  in such a way that the basic transmitter pulse  $g_d(t)$  has the following interpolation points:

$$\text{...}\hspace{0.15cm} , g_3,\hspace{0.25cm}g_2 = 0 ,\hspace{0.15cm}g_1 = 0 ,\hspace{0.15cm}g_0 = 1,\hspace{0.15cm}g_1 = 0 ,\hspace{0.15cm}g_2 = 0 ,\hspace{0.25cm}g_3 ,\hspace{0.15cm} \text{...}$$

$\text{Example 1:}$  We assume the symmetrical input signal according to the upper diagram in the graph. With the abbreviation  $g_m(\nu)= g_m(\pm \nu \cdot T)$  there are the following samples at the distance of the symbol duration  $T$:

$$g_m(t) = {\rm e}^{ - \sqrt{2 \hspace{0.05cm} \cdot \hspace{0.05cm}\vert\hspace{0.05cm} t \hspace{0.05cm} \vert /T} }\hspace{0.3cm} \Rightarrow \hspace{0.3cm} g_m(0) = 1 ,\hspace{0.35cm}g_m(1)= 0.243,\hspace{0.35cm}g_m(2)= 0.135,\hspace{0.35cm}g_m(3)= 0.086, \hspace{0.35cm}g_m(4)= 0.059 \hspace{0.05cm}.$$

For the output pulse  $g_d(t =0) = 1$  and  $g_d(t =\pm T) = 0$  should be valid. For this purpose, a first-order delay filter with coefficients  $k_0$  and  $k_1$ is suitable, which must satisfy the following conditions:

Input and output pulse of the optimal Nyquist equalizer

$$t = \pm T\hspace{-0.1cm} : \hspace{0.2cm}g_1 = k_0 \cdot 0.243 + k_1 \cdot \big [1.000 +0.135 \big ] = 0\hspace{0.3cm}\Rightarrow \hspace{0.3cm}{k_1} = -0.214 \cdot {k_0}\hspace{0.05cm},$$

$$ t = 0 \hspace{-0.1cm} : \hspace{0.6cm}g_0 = k_0 \cdot 1.000 + k_1 \cdot 2 \cdot 0.243= 1\hspace{0.3cm}\Rightarrow \hspace{0.3cm}0.896 \cdot {k_0} = 1 \hspace{0.05cm}.$$

From this, the optimal filter coefficients  $k_0 = 1.116$  and  $k_1 = 0.239$ are obtained.

• The middle diagram shows that thus the first precursor and the first trailer can be compensated and at the same time  $g_d(0) =1$  is valid (yellow background).
• However, the further basic transmitter pulse values (blue circles) are different from zero and cause intersymbol interference.
  
  

The lower diagram shows that with a second order filter  $(N = 2)$  zero crossings are forced at  $\pm T$  and at  $\pm 2T$  if the coefficients  $k_0 = 1.127$,  $k_1 = 0.219$  and  $k_2 = 0.075$  are suitably chosen. The system of equations for determining the optimal coefficients is thereby:

$$t = 0\hspace{-0.1cm}:\hspace{0.85cm}g_0 = k_0 \cdot 1.000 + k_1 \cdot 2 \cdot 0.243 + k_2 \cdot 2 \cdot 0.135 = 1\hspace{0.05cm},$$

$$t= \pm T\hspace{-0.1cm}:\hspace{0.45cm}g_1 = k_0 \cdot 0.243 + k_1 \cdot \big [1.000+0.135 \big ]+ k_2 \cdot \big [0.243+0.086 \big ] = 0\hspace{0.05cm},$$

$$t = \pm 2 T\hspace{-0.1cm}:\hspace{0.2cm}g_2 = k_0 \cdot 0.135 + k_1 \cdot \big [0.243+0.086\big ]+ k_2 \cdot \big [1.000 + 0.059 \big ]= 0 \hspace{0.05cm}.$$

$\text{Conclusion:}$  The results can be generalized as follows:

• With an  $N$–th order delay filter, the main value  $g_d(0)$  can be made one (normalized), and the first $N$  trailers  $g_{\nu}$  and the first $N$  precursors  $g_{-\nu}$  can be made zero.
  

• Further precursors and trailers  $(\nu \gt N)$  cannot be compensated in this way. It is even possible that the precursors and trailers outside the compensation range are enlarged or even new ones are created.
  

• In the limit  $N \to \infty$  (in practice this means:   a filter with very many coefficients) a complete Nyquist equalization and thus an intersymbol interference free transmission is possible.

Description in the frequency domain

The fact that the optimal Nyquist equalizer is multiplicatively derived from

• the matched filter  $H_{\rm MF}(f) = H_{\rm S}^\star (f)\cdot H_{\rm K}^\star(f)$  – i.e. matched to the basic receiver pulse  $g_r(t)$  – and
  
• a transversal filter  $H_{\rm MF}(f)$  with infinitely many filter coefficients
  
  

follows from the first Nyquist criterion. By applying the  "calculus of variations",  the frequency response of the transversal filter is obtained – see [TS87]:

$$H_{\rm TF}(f) = \frac{1}{\sum\limits_{\kappa = -\infty}^{+\infty} |H_{\rm SK}(f - \frac{\kappa}{T}) |^2} \hspace{0.3cm}{\rm{mit}}\hspace{0.3cm}H_{\rm SK}(f) = H_{\rm S}(f)\cdot H_{\rm K}(f) \hspace{0.05cm}.$$

The left graph shows the function  $20 \cdot \lg \ H_{\rm TF}(f)$  in the range  $| f | \le 1/T$. This assumes rectangular NRZ transmission pulses and a coaxial cable with the characteristic cable attenuation  $a_\star$.

(Magnitude) frequency response of the transversal filter (left) and the entire optimal Nyquist equalizer (right)

One can see from the above equation and the left graph:

• $H_{\rm TF}(f)$  is real, which results in the symmetrical structure of the transversal filter:   $k_{-\lambda} =k_{+\lambda} $.
  
• $H_{\rm TF}(f)$  is at the same time a function periodic with frequency  $1/T$. 
  
• The coefficients are thus obtained from the  Fourier series  (applied to the spectral function):

$$k_\lambda =T \cdot \int_{-1/(2T)}^{+1/(2T)}\frac{\cos(2 \pi f \lambda T)} {\sum\limits_{\kappa = -\infty}^{+\infty} |H_{\rm SK}(f - {\kappa}/{T}) |^2} \hspace{0.2cm} {\rm d} f \hspace{0.25cm}\Rightarrow \hspace{0.25cm}H_{\rm TF}(f) = \sum\limits_{\lambda = -\infty}^{+\infty} k_\lambda \cdot {\rm e}^{-{\rm j}2 \pi f \lambda T}\hspace{0.05cm}.$$

The right graph shows the frequency response  $20 \cdot \lg \ |H_{\rm E}(f)|$  of the entire receiver filter including the matched filter. It holds:

$$H_{\rm E}(f) = H_{\rm MF}(f) \cdot H_{\rm TF}(f) = \frac{H_{\rm SK}^{\star}(f)}{\sum\limits_{\kappa = -\infty}^{+\infty} |H_{\rm SK}(f - {\kappa}/{T}) |^2}.$$

To these representations it is to be noted:

• For  $a_\star = 0 \ \rm dB$  (ideal channel, green zero line) the transversal filter $H_{\rm TF}(f)$ can be omitted and it is valid for NRZ rectangular pulses as already derived in the section  "Optimal binary receiver – "Matched Filter" realization": 

$$H_{\rm E}(f) =H_{\rm S}(f) = {\rm si} (\pi f T).$$

• While the transversal filter frequency response  $H_{\rm TF}(f)$  is symmetrical to the Nyquist frequency  $f_{\rm Nyq} = 1/(2T)$  at  $a_\star \ne 0 \ \rm dB$,  this symmetry is no longer given for the receiver filter overall frequency response  $H_{\rm E}(f)$. 
  
• The maxima of the frequency responses  $H_{\rm TF}(f)$  and  $|H_{\rm E}(f)|$  depend significantly on the characteristic cable attenuation  $a_\star$.  From the blue and red function curves, respectively, can be read:

$$a_{\star} = 40\,{\rm dB}\hspace{-0.1cm}:\hspace{0.2cm}{\rm Max}\big[H_{\rm TF}(f)\big]\hspace{0.1cm} \approx 80\,{\rm dB}, \hspace{0.2cm}{\rm Max}\big[\ |H_{\rm E}(f)| \ \big] \approx 40\,{\rm dB}\hspace{0.05cm},$$

$$a_{\star} = 80\,{\rm dB}\hspace{-0.1cm}:\hspace{0.2cm}{\rm Max}\big[H_{\rm TF}(f)\big] \approx 160\,{\rm dB}, \hspace{0.2cm}{\rm Max}\big[\ |H_{\rm E}(f)|\ \big] \approx 80\,{\rm dB}\hspace{0.05cm}.$$

Approximation of the optimal Nyquist equalizer

Optimum Nyquist frequency response for a coaxial cable

We now consider the overall frequency response between the Dirac source and the decision.

• This is made up multiplicatively of the frequency responses of the transmitter, channel and receiver.
• According to the derivation, the total frequency response must satisfy the Nyquist condition:

$$H_{\rm Nyq}(f) = H_{\rm S}(f) \cdot H_{\rm K}(f) \cdot H_{\rm E}(f) = \frac{|H_{\rm SK}(f)|^2}{\sum\limits_{\kappa = -\infty}^{+\infty} |H_{\rm SK}(f - {\kappa}/{T}) |^2}\hspace{0.05cm}.$$

The graph shows the following properties of the optimal Nyquist equalizer (ONE):

• If the cable attenuation is sufficiently large  $(a_\star \ge 10 \ \rm dB)$, the overall frequency response can be described with good approximation by the   cosine rolloff low-pass filter. 
  

• The larger  $a_\star$  is, the smaller is the rolloff factor  $r$  and the steeper is the edge drop. For the characteristic cable attenuation  $a_\star = 40 \ \rm dB$  (blue curve) we get  $r \approx 0.4$, for  $a_\star = 80 \ \rm dB$  (red curve) $r \approx 0.18$.
  

• Above the frequency  $f_{\rm Nyq} \cdot (1 + r)$,   $H_{\rm Nyq}(f)$  has no components. However, with ideal channel   ⇒    $a_\star = 0 \ \rm dB$  (green curve),  $H_{\rm Nyq}(f)= {\rm si}^2(\pi f T)$  theoretically extends to infinity.

The interactive applet "Frequency & Impulse Responses" illustrates, among other things, the properties of the cosine rolloff low–pass filter.

Calculation of the normalized noise power

We now consider the (normalized) noise power at the decision. For this holds:

$$\sigma_{d,\hspace{0.05cm} {\rm norm}}^2 = \frac{\sigma_d^2}{N_0/ (2T)} =T \cdot \int_{-1/(2T)}^{+1/(2T)} |H_{\rm E}(f)|^2 \,{\rm d} f .$$

To calculate the normalized noise power at ONE

• The left plot of the graph shows  $|H_{\rm E}(f)|^2$  in linear scale for the characteristic cable attenuation  $a_\star = 80 \ \rm dB$. Note that  $|H_{\rm E}(f = 0)|^2 = 1$. 

• Since the frequency has been normalized to  $1/T$  in this plot, the normalized noise power corresponds exactly to the area (highlighted in red) under this curve. The numerical evaluation results in:

$$\sigma_{d,\hspace{0.05cm} {\rm norm}}^2 = 1.68 \cdot 10^7\hspace{0.3cm}\Rightarrow \hspace{0.3cm} 10 \cdot {\rm lg}\hspace{0.1cm}\sigma_{d,\hspace{0.05cm} {\rm norm}}^2 \approx 72.25\,{\rm dB} \hspace{0.05cm}.$$

• It can be shown that the normalized noise power can be calculated using the transverse filter frequency response  $H_{\rm TF}(f)$  alone, as shown in the right graph:

$$\sigma_{d,\hspace{0.05cm} {\rm norm}}^2 = T \cdot \int_{-1/(2T)}^{+1/(2T)} H_{\rm TF}(f) \,{\rm d} f \hspace{0.3cm}(= k_0)\hspace{0.05cm}.$$

• The red surfaces are exactly the same in both images.

$\text{Conclusion:}$  The normalized noise power of the optimal Nyquist equalizer is equal to the Fourier coefficient  $k_0$ when the real, symmetric, and periodic transverse filter frequency response  $H_{\rm TF}(f)$  is represented as a Fourier series.

Coefficients of the optimal Nyquist equalizer

• In the second column of the table,  $10 \cdot \lg \ (k_0)$  is given depending on the characteristic cable attenuation  $a_\star$  of a coaxial cable.
• Due to the chosen normalization, the table is also valid for  redundancy-free multi-level systems; here  $M$  denotes the number of levels.
  
• The coefficients  $k_1$,  $k_2$,  $k_3$, ... of the transversal filter have alternating signs for  $a_\star \ne 0 \ \rm dB$. 
• For  $a_\star = 40 \ \rm dB$,  four coefficients are greater in magnitude than  $k_0/10$, and for  $a_\star = 80 \ \rm dB$  even seven.

Comparison based on the system efficiency

For a system comparison, the  system efficiency is suitable, which relates the achievable detection SNR  $\rho_d$  to the maximum SNR  $\rho_{d, \ {\rm max}}$,  which, however, is only achievable for ideal channel  $H_{\rm K}(f) \equiv 1$.  For the system efficiency, with  $M$–level transmission and optimal Nyquist equalization:

$$\eta = \frac{\rho_d}{s_0^2 \cdot T / N_0}=\frac{{\rm log_2}\hspace{0.1cm}M}{(M-1)^2 \cdot k_0}.$$

The (normalized) noise power  $k_0$  can be read from the  "table"  auf der letzten Seite abgelesen werden. Beachten Sie die Normierung der charakteristischen Kabeldämpfung  $a_\star$  in der ersten Spalte. Die folgende Tabelle aus [TS87] ermöglicht einen Systemvergleich für die charakteristische Kabeldämpfung  $a_\star = 80 \ \rm dB$.

Vergleich binärer und mehrstufiger Ünertragungssysteme gemäß  $\text{GTP}$  bzw.  $\text{ONE}$

Verglichen werden:

• der gaußförmige Gesamtfrequenzgang  $\text{(GTP)}$, der auch bei Optimierung zu einem impulsinterferenzbehafteten System führt,
  

• der  optimale Nyquistentzerrer  $\text{(ONE)}$, mit dem Impulsinterferenzen per se ausgeschlossen werden.

$\text{Fazit:}$  Die Ergebnisse dieses Systemvergleichs können wie folgt zusammengefasst werden:

• Im binären Fall  $(M = 2)$  ist das impulsinterferenzfreie System  $\text{(ONE)}$  um etwa  $6 \ \rm dB$  besser als das impulsinterferenzbehaftete System  $\text{(GTP)}$.
  
• Wendet man die optimale Nyquistentzerrung bei Mehrstufensystemen an, so ist gegenüber  $\text{GTP}$  ein weiterer, deutlicher Störabstandsgewinn möglich. Für  $M =4$  beträgt dieser Gewinn etwa  $18.2 \ \rm dB$.
  
• Das schmalbandige  $\text{GTP}$–System kann allerdings deutlich verbessert werden, wenn man einen Empfänger mit Entscheidungsrückkopplung verwendet. Dieser wird im nächsten Kapitel behandelt.

Wir verweisen an dieser Stelle auf das interaktive Applet Lineare Nyquistentzerrung.

Aufgaben zum Kapitel

Exercise 3.6: Transversal Filter of the Optimal Nyquist Equalizer

Exercise 3.6Z:Optimum Nyquist Equalizer for Exponential Pulse

Exercise 3.7: Optimal Nyquist Equalization once again

Exercise 3.7Z: Regenerator Field Length